HoMedics Thermometer Instructions and Troubleshooting for Infrared Models

Page 12

TROUBLESHOOTING/ERROR CODES

Condition

Possible Cause

Corrective Action

 

 

 

Consistent Low

Temperature reading

The thermometer measurement

temperature readings/

is below

range is 32° – 210.2°F (0°C – 99°).

Displays “Lo”

measurement range

Contact your physician or if you

 

(below 32°F or 0°C).

have or suspect any medical

 

 

problems.

 

The lens may be

Clean the lens gently with a cotton

 

dirty.

 

swab with a small amount of

 

 

 

The thermometer

alcohol on it.

 

Repeat temperature measurement

 

may not be

 

positioned properly.

procedures.

 

 

 

Consistent high

Temperature reading

The thermometer measurement

temperature readings/

is above the

range is 32° – 210.2°F (0° – 99°C)

Displays “Hi”

measurement range

Contact your physician if you have or

 

(above 210.2°F or

suspect any medical problems.

 

99°C).

 

 

 

 

Consistent error

Operating

The product operating range

messages/Displays “Err”

temperature is not

temperature is 60°– 95°F

 

within the permissible

(16°– 35°C). Move to an area within

 

range for

the above specifications, allow the

 

thermometer to adjust to the

 

measurement.

 

environment and repeat temperature

 

 

 

 

measurement procedures.

 

 

 

Low battery warning

Battery power

Replace battery. See the“Inserting

 

is low.

and Replacing Batteries” section of

 

 

this manual.

 

 

 

Low battery warning

Battery power is

Replace battery immediately. See

with “Lo” symbol

too low for the

“Inserting and Replacing Batteries”

 

thermometer to

section of this manual.

 

function.

 

 

 

 

PRODUCT SPECIFICATIONS

Model Number

Model Number TI-150

Power Source

2 AAA batteries

 

 

Measurement Method

Infrared

 

 

Measurement Range

32° – 210.2°F (0° – 99°C)

 

 

 

Person Mode: ± 0.4°F (±0.2°C) between 98.6°F –

Accuracy

102.2°F (36°C – 39°C); and ± 0.5°F (±0.3°C) at less

than 98.6°F (36°C) or greater than 102.2°F (39°C).

 

 

Object Mode: ± 5%

 

 

Memory Capacity

20 memories, 10 in person mode, 10 in object mode

 

 

Sleep Mode

1 minute after last button operation

 

 

Operation Environment

Temperature: 60.8° – 104°F (16° – 14°C) Humidity

up to 95%

 

 

 

Storage Environment

Temperature: -4° – 122°F (-20– 50°C) Humidity up to

95%

 

 

 

Note: If the unit still does not work, contact HoMedics Consumer Relations. Under no circumstance should you disassemble or attempt to repair the unit by yourself. Contact information for HoMedics Consumer Relations Department can be found on the warranty page. These specifications are subject to change without notice.

21

22

Image 12
Contents El manual en Español empieza aLa página Table of Contents Read and Save These Instructions What is normal body temperature? What is a fever? How does this product work?Display Description Using Night Mode To turn night mode on/offInserting and replacing batteries Page Fever Alarm Turn unit on by sliding coverOff How to take a temperature reading of an object Wake thermometer press Scan buttonWhen thermometer is on, press the MEM button To review memory readingsTo clear memory Important Notes Regarding Temperature Measurement Care, Maintenance and CleaningTROUBLESHOOTING/ERROR Codes Termómetro No Touch Información de uso LEA Y Guarde Estas Instrucciones Evite tocar la lente o el área del sensor Pilas¿Cómo funciona este producto? Los díasDescripción DE LA Pantalla Encendido apagadoColocación y cambio de las pilas La pantallaUso del modo nocturno Para activar/desactivar el modo nocturnoLa frente de la persona debe estar limpia y seca Persona apagado De la persona37.7C no garantiza la presencia de fiebre Este producto no sustituye la consulta con un médicoEl botón Mode Cómo tomar la lectura de la temperatura de un objeto8 cm de la sustancia/objeto que desea medir Para revisar la memoria de lecturas Con el termómetro encendido, presione el botón MEM memoriaCuando tome la temperatura de un bebé menor de tres meses Diagnóstico Y Resolución DE PROBLEMAS/CÓDIGOS DE Error