Silver Star INFMANU3270 manual Wiring Harness Installation

Page 11

I I I . I N S T A L L A T I O N

NOTE: If your lift is equipped with an onboard battery, refer to “Onboard Battery Installation.”

6.Install the lift platform kit. Refer to the instructions supplied with the kit.

7.Install the wheel chocks to the lift platform. Refer to “Wheel Chock Installation.”

Wiring Harness Installation

The wiring harness is approximately 25 ft. (7.62 meters) long and will accommodate most vehicles.

NOTE: You may wish to perform a practice run before installing the wiring harness. Route a piece of light rope (equivalent to the gauge of the wiring harness) along the anticipated path observing contact points, potential rubbing/chafing points, and any sharp edges. Remove sharp edges with a fine grade file, then treat the steel with a rust inhibitor or metal sealant.

Follow these steps to route the Exterior Lift System wiring harness:

1.Route the lift system wiring harness (starting at the lift) through the interior of the vehicle until you reach the vehicle battery. See figure 7. You will typically find pass-through points at the rear lighting assemblies, which will enable you to route the cable through the trunk and under the back seat.

2.Conceal the harness behind or under the interior panels of the vehicle (there should be existing holes). Be certain that the harness is protected with a rubber grommet when passing it through the metal panels and into the engine compartment.

3.Inside the engine compartment, secure the harness to the firewall and the inner fender with plastic wire ties. Use care not to cause abrasions to the wiring harness. It is important to secure the wiring harness at various points along its run of the vehicle.

WARNING! Do not cut or shorten the wiring harness. If the harness is too long, coil the excess wire and secure it with plastic wire ties.

4.Connect the red wire to the positive (+) terminal and the black (grounding) wire to the negative (-) terminal of the vehicle battery.

WARNING! Before operating the lift, inspect the wiring harness for proper routing and grounding. Improper routing can cause damage to the harness, and improper grounding can cause damage to the electrical system.

LIFT FRAME

WIRING HARNESS

GROUNDINGWIRE

LIFT WIRING CONNECTION

VEHICLE BATTERY

Figure 7. Wiring Harness Installation

Exterior Lift System

www.silverstarmobility.com

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents SilverStar Phone Number Purchase Date F E T Y G U I D E L I N E SIII N T E N T SInformation Exchange N T R O D U C T I O NInternet and Private Purchases PURCHASER’S Agreement S a F E T Y Product Safety SymbolsS a F E T Y Operator Positioning Lifting Capabilities InstallationLifting NON-PRIDE Products Prelift InspectionHitch Classes Hitch Class InformationFollow these steps to install the lock-down arm I . InstallationExterior Lift System Installation Hitch Tube Assembly Follow these steps to install the Exterior Lift SystemWiring Harness Installation Wiring Harness InstallationFollow these steps to install the wheel chocks Onboard Battery InstallationFollow these steps to install the onboard battery Wheel Chock InstallationFollow these steps to operate the Exterior Lift System O P E R a T I O NExterior Lift System Operation Unlocking the Retractable Tie-down Strap Manual Crank Operation Manual Exterior Lift OperationA T T E R Y C H a R G I N G Battery ChargingFollow these steps to replace the onboard battery figure Battery ReplacementC a R E a N D M a I N T E N a N C E Care and MaintenanceLift Removal General Cleaning GuidelinesWiring Harness Lift Platform/Metal ComponentsWhat if the lift system operates slowly up or down? I . TroubleshootingTroubleshooting What if the motor on my lift system will not operate?I I . W a R R a N T Y THREE-YEAR Transferable Limited WarrantyONE-YEAR Warranty Service Checks and Warranty ServiceSpecifications P E N D I X I Specification SINFMANU3279
Top Page Image Contents