Braun Corporation FMVSS No. 403 Quick Reference Installation Sheet 31312
-AINTENANCEEANDA,UBRICATION
Proper maintenance is necessary to ensure safe, troublefree operation. Inspecting the lift for any wear, damage or other abnormal conditions should be a part of your daily routine. Simple inspections can detect potential problems.
The maintenance and lubrication procedures specified in this schedule must be performed by a Braun authorized service representative at the scheduled intervals according to the number of cycles.
The Vangater II is equipped with hardened pins and
ponents are replaced, grease must be applied during instal- lation procedures. Specified lubricants are available from The Braun Corpora- tion (part numbers provided below).
All listed inspection, lubrication and main- tenance procedures should be repeated at “750 cycle” intervals
WARNING
Maintenance and lu- brication procedures must be performed as specified by an authorized service technician. Failure to do so may result in serious bodily injury and/or prop- erty damage.
|
| Specified (recommended) | Available | Braun | |
Lubricant |
| Type | Lubricant | Amount | Part No. |
Light Oil |
| Light Penetrating Oil | LPS2, General Purpose | 11 oz. | 15807 |
| (30 weight or equivalent) | Penetrating Oil | Aerosol Can | ||
| Stainless Stick | 1.68 oz. | 15806 | ||
| Style (tube) | Stick (tube) |
| ||
|
|
|
| ||
Light Grease | Light Grease | Lubriplate | 14 oz. | 15805 | |
(Multipurpose) |
| Can | |||
|
|
| |||
| Downstop pivot points (2) | Apply Light Oil - See Lubrication Diagram | |||
| Upper lift rod pin | Apply Light Oil - See Lubrication Diagram | |||
Lower lift rod pin | Apply Light Oil - See Lubrication Diagram | ||||
|
|
|
|
| |
#YCLES | Kickout spring (located in switch arm) | Apply Light Oil - See Lubrication Diagram | |||
life of the lift.
When servicing the lift at the recommended inter- vals, inspection and lubrication procedures speci- fied in the previous sections should be repeated. Clean the components and the surrounding area before applying lubricants. LPS2 General Purpose Penetrating Oil is recommended where Light Oil is called out. Use of improper lubricants can attract dirt or other contaminants which could result in wear or damage to the components. Platform components exposed to contaminants when lowered to the ground may require extra attention.
Lift components requiring grease are lubricated during assembly procedures. When these com-
following the scheduled “4500 Cycles” maintenance. These intervals are a general guideline for scheduling maintenance procedures and will vary according to lift use and conditions. Lifts exposed to severe condi- tions (weather, environment, contamination, heavy usage, etc.) may require inspection and maintenance procedures to be performed more often than speci- fied.
Discontinue lift use immediately if maintenance and lubrication procedures are not properly per- formed, or if there is any sign of wear, damage or improper operation. Contact your sales representa- tive or call The Braun Corporation at
| Platform hinges (6) | Apply Light Oil - See Lubrication Diagram | |||
| Outboard barrier latch | Apply Light Oil - See Lubrication Diagram | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Perform all procedures listed in previous section also |
|
|
| |
| Inboard locator latch mechanism | Apply Light Grease - See Lubrication Diagram | |||
Check mounting hardware | Tighten, repair or replace if needed. | ||||
|
|
|
|
| |
#YCLES | Check all fasteners (snap rings, nuts, hairpins, etc.) | Tighten, resecure or replace if needed. | |||
| Check all pivot points for excessive wear | Resecure, replace damaged parts or otherwise | |||
|
|
| correct as needed. Note: Apply lubricant during | ||
|
|
| reassembly procedures. | ||
|
|
|
|
| |
|
|
|
| ||
|
|
|
|
|
|
|
| Perform all procedures listed in previous sections also |
| ||
|
| Platform fold mechanism | Apply Light Grease - See Lubrication Diagram | ||
| Ballscrew / main drive | Add Lucas Heavy Duty Oil Stabilizer | |||
#YCLES |
| ||||
|
|
|
|
| |
|
| Clean ground cable at battery and frame |
|
|
|
Main Drive Ballscrew
(in Frame Tube - hidden)
Switch Arm
Lift Rod
Downstop
(hidden)
Drive Arms
Inboard Locator
Latch Mechanism
Platform Fold
Mechanism
(Under Cover)
| Check power cables |
|
|
|
|
#ONSECUTIVE | Repeat all previously listed inspection, lubrica- |
#YCLE# | tion and maintenance procedures at 750 cycle |
)NTERVALS | intervals. |
| |
|
|
Platform
Hinges (6)
Outer Barrier Latch