Radio Shack 43-3557 owner manual Troubleshooting, Problem Solution

Page 33

TROUBLESHOOTING

If your phone is not performing to your expectations, please try these simple steps first

Problem

Solution

Troubleshooting

 

 

 

 

 

• Make sure the AC adapter is plugged into the

 

The CHARGE/IN USE

base and wall outlet.

 

indicator won’t illuminate

• Make sure the handset is properly seated on the

 

when the handset is placed

base.

 

on the base.

• Make sure the charging contacts on the handset

 

 

and base are clean.

 

 

 

 

 

• Make sure that the base antenna is in a vertical

 

 

position.

 

 

• Move the handset and/or base to a different

 

The audio sounds weak

location away from metal objects or appliances

 

and try again.

 

and/or scratchy.

 

• Press CH/DELETE to help eliminate

 

 

 

 

background noise.

 

 

• Make sure that you are not too far from the

 

 

base.

 

 

• Check both ends of the base telephone line cord.

 

 

• Make sure the AC adapter is plugged into the

 

Can’t make or receive calls.

base and wall outlet.

 

• Disconnect the AC adapter for a few minutes.

 

 

Then reconnect it.

 

 

• Make sure that you are not too far from the base.

 

 

 

 

 

• The battery pack may be weak. Charge the

 

 

battery for 15-20 hours.

 

The handset doesn’t ring or

• The handset may be too far away from the base

 

receive a page.

unit.

 

 

• Place the base unit away from appliances or

 

 

metal objects.

 

 

• Keep the handset away from microwave ovens,

 

 

computers, remote control toys, wireless

 

 

microphones, alarm systems, intercoms, room

 

Severe noise interference.

monitors, fluorescent lights, and electrical

 

 

appliances.

 

 

• Move to another location or turn off the source

 

 

of interference.

 

 

 

 

33

Image 33
Contents Caller ID/Call Waiting ID GHz Cordless TelephoneContents Introduction IntroductionInformation FCC StatementImportant Information Surge Protection Important Safety Instructions Important Safety InstructionsImportant Caller ID Information Important Caller ID InformationInstallation InstallationSelecting a Location On a Desk TOP On a Wall Plate or WallCONNECTING/CHARGING the Battery Pack Installation Installation Operation Making and Receiving CallsOperation Earpiece Volume Handset Ringer Tone and VolumeAdjusting the Handset Ringer and Earpiece Volume Temporarily Mute RingerTone Dialing SWITCH-OVER Traveling OUT-OF-RANGESelecting a Different Channel Voice Mail Waiting Indicator Voice Mail Waiting IndicatorFlash and Call Waiting Choosing the Dialing Mode Setting Menu OptionsChanging the Auto Talk Entering Your Area CodeChoosing the Dialing Mode Memory Dialing Setting the LanguageStoring Phone Numbers and Names Memory DialingSee Steps for Entering Names and Special Characters on Use PAUSE/REDIAL to enter a pause Steps for Entering Names and Special CharactersIf you make a mistake while entering a name Memory Dialing from Talk Mode Memory Dialing from Standby ModeMaking Calls with Memory Dialing Chain DialingEditing a Stored Name AND/OR Phone Number Use the number key, /TONE/, # Erasing a Stored Name and Phone NumberONE-TOUCH Speed Dial Testing Stored Emergency NumbersStoring and Editing the Speed Dial Ô Making Calls with the Speed DialDeleting the Speed Dial When the Telephone Rings Caller IDCaller ID Viewing the Caller ID Message List Deleting a Caller ID MessageDeleting Information from the Caller ID List Viewing the Caller ID Message ListDeleting all Caller ID Names/ Numbers Ô Using the Caller ID ListCalling a Party from the Caller ID List Deleting all Caller ID Names/NumbersLong Distance Calls Area Code Setting Cancellation Long Distance Calls and Area Code Setting/CancellationStoring Caller ID Messages in Memory Dialing Storing Caller ID Messages in Memory DialingHeadset Installation Installing the BeltclipAdditional Information To attach the beltclipProblem Solution TroubleshootingService and Repair CareCare Page RadioShack Corporation