29385
Call Waiting Caller ID Speakerphone with 13 Number Memory User’s Guide
INTRODUCTION
CAUTION: When using telephone equipment, there are basic safety instructions that should always be followed. Refer to the IMPORTANT SAFETY INSTRUCTIONS provided with this product and save them for future reference.
Your Caller ID phone stores and displays specific information, provided by your local telephone company, to subscribers of Caller ID or similar caller identification services.
Your Caller ID phone enables you to:
•Identify callers before you answer the phone.
•View the time and date of each incoming call.
•Record up to 75 Caller ID messages sequentially.
IMPORTANT: In order to use all of the features of this telephone, you must subscribe to two
separate services available from your local telephone company: the standard Name/Number Caller ID Service to know who is calling when the phone rings and Caller ID with Call Waiting Service to know who is calling while you are on the phone.
SHORT GLOSSARY OF TERMINOLOGY USED IN
• With the rounded end of the pedestal pointing upward, insert the tab on the end of the pedestal into the middle slot on the bottom of the base, then push the pedestal down until the two tabs on the left and right corners of the pedestal snap (lock) into the two lower slots on the bottom of the base.
•Slip the mounting holes over the wall plate posts and firmly slide the unit down into place (wall plate not included).
SETTING UP THE CALLER ID MENU
You should not plug the telephone into the modular jack while setting up the Caller ID menu.
1.Press the MENU button to enter the menu feature configuration mode.
#1. >ENG FRA ESP (CID language default English)
#2. CONTRAST (default level is 3).
#3. LOCAL AREA CODE
#4. TONE/PULSE (Default is tone dialing).
2. Press the MENU button to scroll through the 4 menu screens. |
CALLER ID DISPLAY MESSAGES
The following special messages indicate the status of a message or the unit:
BLOCKED CALL | The caller of the incoming call is registered as “Private | |
|
| Number” and their Caller ID information is withheld. |
CALL WAITING | Indicates a call is waiting on the line. | |
|
| Battery power level is low. |
|
| |
NO CALLS | The caller memory is empty. | |
START/END | You are at the beginning or the end of the Caller ID memory log. | |
UNKNOWN CALLER | The incoming call does not have Caller ID service or their service | |
|
| area is not linked to yours. If UNKNOWN CALLER appears along |
|
| with a calling number, the name information for that number was |
|
| not available. |
SPEAKERPHONE BASICS
MEMORY
You may store information in any of the following memory locations: 0 to 9, A, B, and C . See “Storing a Pause in Memory” and “Temporary Tone Dialing” for more information.
STORING A NAME AND NUMBER IN MEMORY
1.Press the STORE button. LOCATION? shows in the display.
2.Press the desired memory location
NOTE: You may select memory locations by pressing or to scroll through the memory locations or press the 0 - 9, A, B, C.
3. | Press the STORE button again to confirm the memory location. |
| NOTE: If necessary, to erase existing memories, or if you make a mistake, use the |
| DELETE button. |
4. | Use the number keys to enter the telephone number (up to 32 digits) and press the STORE |
| button to save. (The unit will not dial a phone number in this mode.) The cursor |
| automatically moves to the text line for name entry. |
5. | Use the number keys to enter the name of the person associated with the telephone number |
| you just entered. More than one letter is stored in each of the number keys. |
Phone Does Not Ring
•Make sure ringer switch is ON.
•You may have too many extension phones on your line. Try unplugging some extension phones.
•Check for dial tone. See Troubleshooting Tips for No Dial Tone.
Incoming Voice Volume Low
•Are other phones off hook at same time? If so, this is normal condition as volume drops when additional phones are used at once.
•Check the handset receiver or speaker volume.
Memory Dialing
•Make sure you entered the numbers correctly into memory.
GENERAL PRODUCT CARE
To keep your phone working and looking good, follow these guidelines:
• | Avoid putting it near heating appliances and devices that generate electrical noise (for |
| example, motors or fluorescent lamps). |
• | DO NOT expose to direct sunlight or moisture. |
We bring good things to life.
THIS MANUAL
Hook switch. The part of the phone that pops up to activate the phone line when the handset is lifted from the base.
BEFORE YOU BEGIN
PARTS CHECKLIST
Make sure your package includes the following items:
Base | Handset | Handset cord Desktop/wall | |
|
| mounting pedestal | line cord |
|
|
| Wall plate |
3. Use the | or | buttons to select the desired setting. |
NOTE: You have 20 seconds following an entry before the phone returns to the Summary Screen.
DISPLAY LANGUAGE
This adjustment allows you to display the Caller ID prompts in English, French, or Spanish.
1. Press the MENU button until ENG FRA ESP shows in the display.
2. Use the or buttons to select ENG, FRA or ESP.
3. Press the MENU button again to save.
CONTRAST
This adjustment allows you to adjust the contrast of the display.
1. Press the MENU button until CONTRAST shows in the display.
2. Use the | or | buttons to select level 1, 2, 3, 4, or 5. |
3. Press the MENU button again to save.
LOCAL AREA CODE
The telephone uses the programmed area codes to determine the number format to display when a valid Caller ID signal is received. Numbers that match the local area code are displayed as seven digits and are used for dialing back previous numbers. Entering your local area code will also help you immediately know if the call is local or long distance when viewing the CID records in the display.
NOTE: If you make a mistake and want to start over again, press the DELETE button to erase all of the digits.
DELETE
button
STORE
button
MUTE button
VOL
button
LOCATION
display
DIAL button
MENU button
FLASH/EXIT
button
REDIAL/PAUSE SPEAKER button
button
For example, to enter the name BILL SMITH, press the 2 key twice for the letter B. Press the |
4 key 3 times for the letter I. Press the 5 key 3 times for the letter L. |
NOTE: The flashing cursor automatically moves to the next position or you may press
the | or | buttons to move the cursor to the next position. |
Press the 5 key 3 times for the second letter L. Press the arrow key (4) two times to insert a space, and press the 7 key 4 times for the letter S. Press the 6 key once for the letter M. Press the 4 key 3 times for the letter I. Press the 8 key for the letter T. Press the 4 key twice for the letter H.
6.Press the STORE button to save the name.
7.To enter another name and number in a different memory location, return to step 1 and repeat the process.
CHANGING A STORED NUMBER
Repeat the storage sequence under Storing A Name and Number in Memory, and use the DELETE button to delete the old number before entering the new number.
ERASING A STORED NUMBER
1.Press the STORE button.
2.Press the memory location
3.Press the DELETE button.
COPYING CALLER ID MEMORIES TO USER
MEMORY
• Avoid dropping and other rough treatment to the unit. | |
• Clean with a soft cloth. | |
• | Never use a strong cleaning agent or abrasive powder because this will damage the finish. |
• | Retain the original packaging in case you need to ship it at a later date. |
SERVICE
If trouble is experienced with this equipment, for repair or warranty information, please contact customer service at
This product may be serviced only by the manufacturer or its authorized service agents. Changes or modifications not expressly approved by ATLINKS USA, Inc. could void the user’s authority to operate this product. For instructions on how to obtain service, refer to the warranty included in this guide or call customer service at
Or refer inquiries to:
ATLINKS USA, Inc.
Manager, Consumer Relations
P O Box 1976
Indianapolis, IN 46206
Attach your sales receipt to the booklet for future reference or jot down the date this product was purchased or received as a gift. This information will be valuable if service should be required during the warranty period.
Purchase date ________________________________________________
EQUIPMENT APPROVAL INFORMATION
Your telephone equipment is approved for connection to the Public Switched Telephone Network and is in compliance with parts 15 and 68, FCC Rules and Regulations and the Technical Requirements for Telephone Terminal Equipment published by ACTA.
1Notification to the Local Telephone Company
On the bottom of this equipment is a label indicating, among other information, the US number and Ringer Equivalence Number (REN) for the equipment. You must, upon request, provide this information to your telephone company.
The REN is useful in determining the number of devices you may connect to your telephone line and still have all of these devices ring when your telephone number is called. In most (but not all) areas, the sum of the RENs of all devices connected to one line should not exceed 5. To be certain of the number of devices you may connect to your line as determined by the REN, you should contact your local telephone company.
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.
Notes
•This equipment may not be used on coin service provided by the telephone company.
•Party lines are subject to state tariffs, and therefore, you may not be able to use your own telephone equipment if you are on a party line. Check with your local telephone company.
•Notice must be given to the telephone company upon permanent disconnection of your telephone from your line.
•If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this product does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
2Rights of the Telephone Company
Should your equipment cause trouble on your line which may harm the telephone network, the telephone company shall, where practicable, notify you that temporary discontinuance of service may be required. Where prior notice is not practicable and the circumstances warrant such action, the telephone company may temporarily discontinue service immediately. In case of such temporary discontinuance, the telephone company must: (1) promptly notify you of such temporary discontinuance; (2) afford you the opportunity to correct the situation; and (3) inform you of your right to bring a complaint to the Commission pursuant to procedures set forth in Subpart E of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities, equipment, operations or procedures where such action is required in the operation of its business and not inconsistent with FCC Rules and Regulations. If these changes are expected to affect the use or performance of your telephone equipment, the telephone company must give you adequate notice, in writing, to allow you to maintain uninterrupted service.
INTERFERENCE INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is “receiving” the interference).
•Reorient or relocate and increase the separation between the telecommunications equipment and receiving antenna.
•Connect the telecommunications equipment into an outlet on a circuit different from that to which the receiving antenna is connected.
If these measures do not eliminate the interference, please consult your dealer or an experienced radio/television technician for additional suggestions. Also, the Federal Communications Commission has prepared a helpful booklet, “How To Identify and Resolve Radio/TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington, D.C. 20402. Please specify stock number
HEARING AID COMPATIBILITY (HAC)
This telephone system meets FCC standards for Hearing Aid Compatibility.
US NUMBER IS LOCATED ON THE CABINET BOTTOM
REN NUMBER IS LOCATED ON THE CABINET BOTTOM
| ATLINKS USA, Inc. |
| 101 West 103rd Street |
Model 29385 | Indianapolis, IN 46290 |
00000737 (Rev. 2 E/S) | © 2004 ATLINKS USA, Inc. |
Trademark(s) ® Registered | |
Printed in China | Marca(s) Registrada(s) |
TELEPHONE JACK REQUIREMENTS |
|
To use this phone, you need an RJ11C type modular telephone jack, | Modular |
which might look like the one pictured here, installed in your home. If | telephone |
you don’t have a modular jack, call your local phone company to find | line jack |
out how to get one installed. |
|
IMPORTANT INSTALLATION INFORMATION
CAUTION: Disconnect the phone cord from the wall outlet before installing or replacing the batteries.
•Never install telephone wiring during a lightning storm.
•Never touch uninsulated telephone wires or terminals, unless the telephone line has been disconnected at the network interface.
•Use caution when installing or modifying telephone lines.
•Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
•Temporarily disconnect any equipment connected to the phone, such as faxes, other phones, or modems.
INSTALLING AND REPLACING THE BATTERIES
Your Caller ID phone uses 4
IMPORTANT: You will have approximately 90 seconds to replace the batteries before the memories stored are lost. Please read the instructions before replacing the batteries and have the batteries ready to be inserted beforehand.
IMPORTANT: If you are not going to use the telephone for more than 30 days, remove the batteries because they may leak and damage the unit.
1.If the telephone line cord is connected, disconnect it from the base unit.
2.Carefully turn over the phone, and press down and out on the snap tab located on the top of the mounting bracket. Lift
the bracket off.
3. Release latch on battery compartments and remove cover.
4.Insert 4
5.Snap the battery compartment doors back into place and replace the mounting bracket.
6.If the line cord was previously connected,
NOTE: If the low battery icon appears in the display, you need to replace the batteries. It is important that you replace the batteries as soon as possible in order to maintain Caller ID operation.
INSTALLING THE PHONE
Your phone should be placed on a level surface, such as a desk or table top, or you can mount it on a wall. A desktop/wall mounting pedestal is packaged with your phone.
ATTACHING THE DESKTOP PEDESTAL
•Turn the phone over so that the bottom of the base is facing up and the thickest end is facing away from you.
•With the rounded end of the wedge pointing downward, insert the tab on the rounded end of the pedestal into the middle slot on the bottom of the base, then push the pedestal down until the two tabs on the left and right corners of the pedestal snap (lock) into the two upper slots on the bottom of the base.
CONNECTING THE HANDSET
1.Connect one end of the coiled handset cord to the jack on the handset.
2.Plug the other end of the coiled handset cord to the jack on the base.
3.Place the handset in the cradle.
CONNECTING THE TELEPHONE LINE
1.Connect one end of the straight telephone line cord to the jack on the back of the base.
2.Connect the other end to a wall phone jack.
3.Set the RINGER volume switch located at
the back of the base to the desired loudness.
OFF - Telephone will not ring.
LO - Sound will be lowest.
HI - Sound will be loudest.
NOTE: The unit is properly installed if you pick up the handset and hear the dial tone. Otherwise, recheck all installation steps.
WALL MOUNTING
Your speakerphone can also be mounted on a wall plate (not included).
ATTACHING THE WALL MOUNTING PEDESTAL
•Turn the phone over so that the bottom of the base is facing up and the thickest end is pointing away from you.
•If desired gather the extra telephone line cord together and store inside the wall mounting pedestal, and then thread the line cord through the grooves on the pedestal according to the illustration.
1. Press the MENU button until LOCAL AREA CODE shows in the display.
2. Press the | button to select digit. |
3. Press the | button to enter the second and third digit. |
4. Press the MENU button to save.
DIALING MODE
This adjustment allows you to select tone
1. Press the MENU button until TONE/PULSE MODE shows in the display.
2. Press the | or | buttons to show the current dialing mode. The default is TONE dialing. | |
3. To change the dialing mode, press the or | buttons. The display alternates between the | ||
two modes. |
|
|
|
4. Press the MENU button again to save.
NOTE: The phone will exit Set Up after 20 seconds if no buttons are pressed.
REMINDER: The time and date are programmed automatically when the first Caller ID record is successfully received after set up.
CALLER ID (CID) FEATURES
CID SUMMARY SCREEN
The Summary Screen shows the current time, date, and number of new calls to review. It is displayed until any button is pressed.
NOTE: The number of new calls is displayed until all new calls have been reviewed.
RECEIVING AND STORING CID CALLS
This unit receives and displays information transmitted by your local phone company. This information can include the phone number, date, and time; or the name, phone number, date, and time. The unit can store up to 75 calls for later review. When the memory is full, a new call automatically replaces the oldest call in memory. NEW appears in the display for calls received that have not been reviewed.
REVIEWING CID RECORDS
• | Press the | or | buttons to view the call records. |
• | Press the | button to scroll through the call records from the most recent to the oldest. | |
• | Press the | button to scroll through the call records from the oldest to the newest. | |
• When all of the records have been viewed, START/END appears in the display.
DELETING CID RECORDS
•To delete the record shown in the display, press the DELETE button once.
•To delete all records while reviewing, press and hold the DELETE button for about three seconds. DELETE ALL? appears in the display. Press DELETE again to complete.
DIALING BACK
When reviewing Caller ID records, you can dialback the numbers on the display by pressing the DIAL button.
NOTE: If PICKUP PHONE shows in the display, no other changes to the number can be made. The information sent from the telephone company is known to be a valid number for dialing back (used only in very limited areas). Once you pickup the phone, the number is automatically dialed.
IF YOU PROGRAMMED YOUR LOCAL AREA CODE
1. Use the | or | buttons to display the number you want to dial. |
2. Press the DIAL button.
•If you see a number with seven digits (i.e.
•If you see a number with 11 digits (i.e.
NOTE: A timer (10 seconds
3.If you are at
4.To dial the displayed number, and the phone is
IF YOU DID NOT PROGRAM YOUR LOCAL AREA CODE
1. Use th or buttons to display the number you want to dial. You will only see
2. See steps 2 through 4 in the previous section to complete the dialback process.
Your phone features a speakerphone for ease of use and convenience during a phone conversation. At any time during a conversation, you can lift the handset to stop using the speakerphone. Likewise, when you are using the handset, press the SPEAKER button and place the handset in the cradle to switch to the speakerphone.
For best speakerphone performance, avoid the following:
•Areas with high background noise. (The microphone might pick up these sounds and prevent the speakerphone from going into the receiving mode when you finish talking.)
•Surfaces affected by vibration.
•Recessed areas such as in a corner, under a cupboard, or next to a cabinet, which can generate an echo effect.
SPEAKERPHONE USE
Note the following guidelines when using the speakerphone:
•The speakerphone works similar to a
•Stay reasonably close to the phone so that you can be clearly heard by the person to whom you are talking.
•You can adjust the speaker volume by pressing the volume button continuously or pressing the review button
or 
after pressing the volume button.
•The speakerphone indicator light comes on when the speakerphone is in use.
NOTE: Batteries must be installed for the speakerphone to operate.
TELEPHONE BASICS
You can use the telephone by speaking into and listening through the handset, or by using the speakerphone.
RECEIVING A PHONE CALL
1.Lift the handset or press SPEAKER to answer the call.
2.Replace the handset in the cradle or press the SPEAKER button to hang up.
MAKING A PHONE CALL
1.Lift the handset or press the SPEAKER button. Wait for a dial tone.
2.Dial the telephone number you want to call.
3.Replace the handset in the cradle, or press the SPEAKER button to hang up.
VOLUME
You may adjust the handset and speakerphone volume independently with the VOL button or the or buttons. Both handset receiver volume level and speakerphone volume level are saved in memory.
ADJUSTING THE HANDSET RECEIVER VOLUME
While using the handset, you can adjust the speaker volume by pressing the VOL button continuously or pressing the or buttons after pressing the VOL button. REC (Handset Receiver) volume shows in the display.
ADJUSTING THE SPEAKERPHONE VOLUME
While using the speakerphone, you can adjust the speaker volume by pressing the VOL button continuously or pressing the or buttons after pressing the VOL button. SPK volume level shows in the display.
NOTE: Both handset receiver and speakerphone volume return to the default setting (low) if the unit is power up reset.
REDIAL
You may redial the last number you called by pressing the REDIAL button after you hear a dial tone.
NOTE: The redial feature holds the last number (up to 32 digits) that you dialed in memory. If you pressed any other numbers after dialing the phone number (for example, when accessing a
MUTE
Use the MUTE button to interrupt a phone conversation to talk privately with someone else in the room. A conversation can be muted while using the speakerphone or handset.
1.Press the MUTE button. The mute indicator illuminates.
2.Press MUTE again to turn it off.
NOTE: Switching from speakerphone to handset cancels mute.
FLASH
Press FLASH to activate special features of your telephone network, such as call transfer, or special services from your local telephone company, such as call waiting.
TEMPORARY TONE DIALING
If you have pulse (rotary) service and want to access customer calling services (such as telebanking and long distance services) that require tone dialing, you can use this feature to temporarily change from pulse to tone service.
After dialing the telephone number and connecting to the customer calling service,
1.Press and release the TONE (*) button.
2.When you hang up, the telephone automatically returns to pulse dialing mode.
TIP: Temporary Tone can also be used while storing numbers in memory by pressing TONE
(*) at the necessary point in the storage sequence.
1. Press the | or | buttons to view the caller number and name you want to copy. |
2.Press the STORE button.
3.Press the memory location
4.Press the STORE button to enter the edit mode, and then press the STORE button again to edit the name.
NOTE: You may select a different memory location by pressing or to scroll through the memories or press a number key
5.Press the STORE button to confirm and save, and wait for three seconds to exit.
NOTE: If the name you want to enter is longer than 12 characters, only the first 12 characters will be copied into memory.
COPYING REDIAL NUMBERS TO MEMORY
1.Press the REDIAL button while the phone is
2.Press the STORE button.
3.Press any number key
4.Press the STORE button twice to confirm and save, and wait for three seconds to exit.
NOTE: If you want to edit the number, press the STORE button again within three seconds. When you are finished, wait three seconds to exit.
DIALING A NUMBER STORED IN MEMORY
WHILE ON-HOOK
1.Press the DIAL button
2.To select a memory, press any number key
NOTE: You may select a different memory location by pressing or to scroll through the memories or press a number key
3. Press the SPEAKER button, or pick up the handset to dial the displayed number.
DIALING A NUMBER STORED IN MEMORY
1.Lift the handset, or press the SPEAKER button.
2.Press the DIAL button then press a memory location button.
CASCADE DIALING
This process allows you to dial a succession of stored numbers from separate memory locations. This is useful when you must dial several sequences of numbers, such as with frequent calls via a telephone company long distance provider.
For example | Memory location |
Local access number of long distance company | 6 |
Authorization code (ID) | 7 |
Long distance phone number | 8 |
1.Pick up the handset or press SPEAKER.
2.Press DIAL button, then press number “6” for the memory location.
3.Press DIAL button, then press number “7” for the memory location.
4.Press DIAL button, then press number “8” for the memory location.
5.The number dials automatically.
STORING A PAUSE IN MEMORY
The REDIAL button has dual functionality and becomes a pause button when the STORE button is pressed first. It is valid only when storing a number into memory locations. Use the PAUSE (REDIAL) button to insert a pause when a delay is needed in an automatic dialing sequence. For example, when you must dial a 9 to get an outside line or when you enter codes to access your long distance company.
PRE-DIALING
1.With the handset on the cradle, enter the telephone number you wish to call. The telephone number shows in the display.
2.Lift the handset or press the SPEAKER button and the number automatically dials.
NOTE: Use the DELETE button to delete an incorrectly entered number.
TROUBLESHOOTING TIPS
No Dial Tone
•Check all cabling to make sure that all connections are secure and not damaged.
•Check hook switch: Does it fully extend when handset is lifted from cradle?
No Display
•Replace the batteries.
•Check for proper battery installation.
No Information is Shown After the Phone Rings
•Are you subscribed to Caller ID service from your local telephone company?
•Be sure to wait until the second ring before answering.
Phone Dials in Pulse with Tone Service
•Make sure T/P DIAL MODE is set to TONE DIAL. Phone Won't Dial Out with Pulse Service
•Make sure T/P DIAL MODE is set to PULSE DIAL.
Name of store ________________________________________________
LIMITED WARRANTY
What your warranty covers:
•Defects in materials or workmanship.
For how long after your purchase:
•One year, from date of purchase.
(The warranty period for rental units begins with the first rental or 45 days from date of shipment to the rental firm, whichever comes first.)
What we will do:
•Provide you with a new or, at our option, a refurbished unit. The exchange unit is under warranty for the remainder of the original product’s warranty period.
How you get service:
•Properly pack your unit. Include any cables, etc., which were originally provided with the product. We recommend using the original carton and packing materials.
•”Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the product is within the warranty period, must be presented to obtain warranty service.” For rental firms, proof of first rental is also required. Also print your name and address and a description of the defect. Send via standard UPS or its equivalent to:
ATLINKS USA, Inc. c/o Thomson
11721 B Alameda Ave. Socorro, Texas 79927
•Pay any charges billed to you by the Exchange Center for service not covered by the warranty.
•Insure your shipment for loss or damage. ATLINKS accepts no liability in case of damage or loss.
•A new or refurbished unit will be shipped to you freight prepaid.
What your warranty does not cover:
•Customer instruction. (Your Owner’s Manual provides information regarding operating instructions and user controls. Any additional information, should be obtained from your dealer.)
•Installation and setup service adjustments.
•Batteries.
•Damage from misuse or neglect.
•Products which have been modified or incorporated into other products.
•Products purchased or serviced outside the USA.
•Acts of nature, such as but not limited to lightning damage.
Product Registration:
•Please complete and mail the Product Registration Card packed with your unit. It will make it easier to contact you should it ever be necessary. The return of the card is not required for warranty coverage.
Limitation of Warranty:
•THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE HEREBY DISCLAIMED. NO VERBAL OR WRITTEN INFORMATION GIVEN BY ATLINKS USA, INC., ITS AGENTS, OR EMPLOYEES SHALL CREATE A GUARANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY.
•REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER. ATLINKS USA, INC. SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. THIS DISCLAIMER OF WARRANTIES AND LIMITED WARRANTY ARE GOVERNED BY THE LAWS OF THE STATE OF INDIANA. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.
How state law relates to this warranty:
•Some states do not allow the exclusion nor limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts so the above limitations or exclusions may not apply to you.
•This warranty gives you specific legal rights, and you also may have other rights that vary from state to state.
If you purchased your product outside the USA:
•This warranty does not apply. Contact your dealer for warranty information.