NCR 5953 manual LCD 800x600 High-Bright Long-Life Color, LCD Interface, Touch option

Page 64

5-4 Chapter 5: 5953 USB DynaKey Migration

Feature	5953 Wedge	5953 USB
	qualified scanners	Ports section

Power LED	Yes	Yes

Additional ports	No	Three General Purpose
		USB ports for Scanner
		and/or any USB 1.1
		compliant device.

Smartcard Reader	No	Possible Future Option
		(not currently planned)

Fingerprint sensor	No	Planned USB module
		replaces Keylock

LCD 800x600 High-Bright Long-Life Color

The NCR 5953 DynaKey has an 800x600 High-Bright, Long-Life Color LCD panel. The USB and Wedge versions of the DynaKey employ similar panels with similar visibility and endurance characteristics.

LCD Interface

The NCR 5953 Wedge DynaKey was designed at a time when an industry standard for LCD connections had not yet emerged, and therefore used an NCR proprietary interface. The 5953 USB DynaKey has been designed with the now-standard DVI interface, which allows the use of more industry-standard parts.

Touch option

The WEDGE DynaKey is available with an optional touch-screen interface. A touch option is planned, but not yet available, for the USB DynaKey.

Image 64

Contents User Guide Page Safety Requirements Audience PrefacePage Table of Contents USB DynaKey Migration MSR Powered USB 12 V to 2 x 4 Locking Connector Revision Record Radio Frequency Interference Statements Federal Communications Commission FCCCanadian Department of Communications Voluntary Control Council for Interference VcciDeclaration of Conformity European ContactPage Introduction Compatibility FeaturesController Board Multi-Color Power LED External Standard PC Keyboard Connector Keylock PositionsSpecial PC Setup Keypad Layout Three-Track MSR or Two-Track JIS MSRSpeaker Integrated 2 x 20 Customer DisplayOverview Physical Environment Operating RangeStorage Range Transit RangeElectrical Requirements Power ConsumptionCable Length Limitations Dimensions 5953-K023 Checkstand Mount Mm 10.75 200 mm 140 mm 105 mm Site Preparation Hardware Installation Serial Number Location Cable Connector Access Mounting OptionsInstalling a USB DynaKey Installing a Remote Table Top USB DynaKeyDVI Installing an Integrated Customer Display 5972-F04019850 Assemble the post components Phillips PH Screw Integrated Display Bracket 19851 Installing a Checkstand Mounted DynaKey Installing a 5953-K023 Checkstand MountCheckstand Base Upper Half Front Cover Thumbscrew 17323 17449 Powering Up Special Keypad ModePower up the system Hardware Installation Normal Operating Mode Screen Saving Feature Hardware Installation Firmware USB DynaKey CapabilitiesUnique POS Capabilities Fpga Firmware DefaultsNCRUsbKeyboardCtl HID usages NCR Proprietary HID Usages KeymatrixusageProgrammable Key Matrix Double-high/Double-wide KeysKeyboard Matrix for 5953 USB DynaKey Sorted by Offset Sorted by KeyNumberSorted by Offset Sorted by KeyNumber Sorted by Offset Sorted by KeyNumber Configurable Key Click Tone USB DynaKey Tone FrequenciesNCR Platform Software Components NCR USB DynaKey ControlProgramming NCR USB DynaKey Control Parameterization Registry Values Key-Value DefinitionsNCR USB DynaKey Control Data Capture Registry Values Set USB Key Matrix ApplicationCommand-line Parameters Set USB Key Clicks ApplicationCommand-line Parameters Inch USB DynaKey Video Drivers Page USB DynaKey Migration Overview5953 USB DynaKey Migration Discussion LCDLCD Interface LCD 800x600 High-Bright Long-Life ColorTouch option Hot Plug POS-Checkout Style KeyboardDouble-High / Double-Wide Keys Keyboard Programmability Keylock Error ToneKey Click Power LED Scanner portAdditional ports Fingerprint SensorSmartcard Reader Key Re-mapping Registry Manipulation Tool 5953 USB DynaKey Migration USB DynaKey Migration 5953 USB DynaKey Migration Hardware Service Safety RequirementsProblem Isolation Procedures Troubleshooting TableSymptom Probable Cause Solution LED Servicing the DynaKey Module Disassembling the DynaKeyRemoving the Remote Table Top Mount Removing the Back Cover Removing the MSR MSR Cleaning Cards Removing the Speaker AssemblyRemoving the Controller Board 20067 Removing the LCD Remove the screws 4 that secure the LCD to the LCD Bracket Removing the Keypad Removing the Keylock Adapter Assembly Replacing the Keylock assembly Re-Assembling the DynaKeyConnector Identification Controller BoardConnector Pin-Out Information DVI ConnectorPowered USB Connector USB Connectors Powered USB 12 V to 2 x 4 Locking Connector CablesDVI to DVI DVI to ChampDynaKey Cleaning Procedures Cleaning the GlassIndex NCRUsbKeyboardCtl, 4-12,4-13