Huawei MC509 CDMA LGA manual Power Supply Features, Input Power Supply

Page 51

错误！未知的文档属性名称
Hardware Guide				Electrical and Reliability Features

	Parameter	Description	Minimum Value	Maximum Value	Unit

	IOL	Low-level output		-1.5	mA
		current

VDD_PX is 2.6V or 1.8V, about the voltage, please refer to Table 3-1 .

5.5 Power Supply Features

5.5.1 Input Power Supply

Table 5-4lists the requirements for input power of the MC509 module.

Table 5-4Requirements for input power of the MC509 module

Parameter	Minimum	Typical	Maximum		Ripple	Unit
	Value	Value	Value
	Value	Value	Value

VBAT	3.0	3.8	4.2		< 50mVpp	V
					(0Hz to 2.5GHz)

VCOIN	1.5	3.0	3.25		< 30mVpp	V

Figure 5-1lists the Power Supply During Burst Emission

Figure 5-1Power Supply During Burst Emission

Table 5-5Requirements for input current of the MC509 module

Power	Peak (Maximum)	Normal (Maximum)

3.8V	<1500mA	<1000mA

	Issue 01 (2011-04-08)	Huawei Proprietary and Confidential	51
		Copyright © Huawei Technologies Co., Ltd.

Image 51

Contents

Hardware Guide Issue DateNo Warranty About This Document HistoryVersion Date Chapter Descriptions Chapter Details SummaryDescription of the Application Interfaces ContentElectrical and Reliability Features Safety Information Product name RF Band Bandwidth IntroductionFunction Overview Feature DescriptionOverall Description About This ChapterTBD SMS Waste Electrical and Electronic Equipment DirectiveWEEE Circuit Block Diagram2Application block diagram of the MC509 module Application Block DiagramLGA Interface Description of the Application InterfacesMin Typical Max Pin Name Description DC Characteristics NormalUimvcc JtagtmsVCCEXT2 VCCEXT1MIC1N WdisableMIC2N MIC1PUartrts Gpio Wakeupout GpioJtagtdo Uartdsr GpioUartrx Gpio PoweronoffUimreset Uartring GpioSpkroutn EaroutnEaroutp SpkroutpAuxant Gpsant135 132133 134Overview Power InterfaceVbat Interface Real-time clock Sudden momentary power lossSmpl timer setting Capacitor value Capacitor package Vcoin InterfaceUimvcc PIN Output Power Supply Interface4Coin cell characteristics Parameter Specifications HB-414 ML-seriesPin Pin Name Description DC Characteristics Min Typical Max Signal Control InterfaceInput Signal Control Pins 3shows the connections of the Poweronoff and Resinn pins Power-On Time SequenceParameter Comments TimeNominal values Units Parameter Comments TimeNominal Units ValuesResinn Output Signal Control Pin TBD Wakeupin SignalUart Interface 6Connections of the Wakeupin and Wakeupout pinsCircuit Recommended for the Uart Interface Pin No Pin Name Description USB data signal D+USB data signal D USB InterfaceVOHmin VOLmax VIHmin VILmax 10DC Electrical Characteristics of USBCircuit Recommended for the UIM Card Interface UIM Card InterfaceNull UimpwrAudio Interface ESD Protection for the UIM Card InterfaceAnalogue Audio DCE Pcmdou Digital AudioPcmsync PcmdinName Min Type Max Primary ModeGeneral Purpose I/O Interface Pin No DescriptionRF Antenna Interface Pin No Pin Name Description DC Characteristics Min Type MaxVCCEXT2 6V Power Jtag InterfaceNC Pins Pin No Description DC Characteristics Name Min Typical MaxGpsant RF GPS 错误！未找到引用源。 shows the RF bands supported by MC509 RF bands RF SpecificationsAntenna Installation Guidelines Operating FrequenciesTest Standards Conducted Rx Sensitivity and Tx PowerConducted RF Measurement Test EnvironmentAntenna Efficiency Conducted Transmit PowerAntenna Design Indicators Antenna Design RequirementsPolarization Radiation PatternGain and Directivity Cdma Antenna Requirements Interference Cdma Antenna Requirements Antenna for MC509 must fulfill the following requirementsRadio Test Environment Passive TestsActive Tests Input voltage of standby Power for the RTC Data pin voltage Electrical and Reliability FeaturesSymbol Specification Minimum Maximum Unit Value External power voltageParameter Description Minimum Value Maximum Value Unit Working and Storage Temperatures and HumidityElectrical Features of Application Interfaces Specification Minimum Value Maximum Value UnitParameter Minimum Typical Maximum Ripple Unit Value Power Supply FeaturesInput Power Supply Power Peak Maximum Normal MaximumTest Condition Standard Reliability FeaturesPower Consumption Working mode Max UnitTest Condition Standard − USB EMC and ESD FeaturesDimensions and interfaces Mechanical SpecificationsPCB Pad Design 2PCB pad design LabelNameplate Packing SystemJgpssi CertificationsCertification FCC CCC NCC TickRestricted Substance Density Threshold ppm Environmental Protection Certification and TestRoHS SGS RoHS TestWeee Importance of Product Certification National Compulsory CertificationPVC-free Product CertificationProduct Certification Classifications Certification Modes DOC Certification Types CE CertificationFCC Certification NCC DGT Certification Comply with the following rules when making DGT marks Telecom Engineer Center Telec Tick CertificationTelec and Jate Certification Japan An example of the DGT markIC XXXXXX-YYYYYYYY Xxxxxx is the company number issued by the IC Huawei 6369AIC Certification Canada  Jate Yyyyyyyy Chinese CertificationsIssue 01 Huawei Proprietary and Confidential RoHS, REACH, JGPSSI, and Chinese Environmental Protection  CCC− PBB − Pbde Huawei MC509 Cdma LGA Module Hardware Guide Certifications CE Certification and FCC Certification Guide to Product CertificationNCC Certification GCF and PtcrbGCF Certification IC CertificationHuawei MC509 Cdma LGA Module Hardware Guide Certifications Ptcrb Certification Overall-System CertificationWcdma FDD Overall-System GCF Certification Overall-System Ptcrb Certification GCF and Ptcrb Certification Area with Inflammables and Explosives Safety InformationInterference Medical DeviceEnvironment Protection Safety of ChildrenTraffic Security Airline SecuritySpecific Absorption Rate SAR Care and MaintenanceLaws and Regulations Observance Emergency CallRegulatory Information CE Approval European UnionFCC Statement Appendix a Circuit of Typical Interfaces Page Acronym or Abbreviation Expansion Appendix B Acronyms and AbbreviationsTTL PDURTC UIM