Sanyo CLT-E33, CLT-E30, CLT-E32 instruction manual Getting Started E 1

Page 13

UP383BA_0.book Page 11 Thursday, May 26, 2005 10:48 AM

GETTING STARTED

1) Press down on the handset battery case cover (use the finger indention for a better grip) and slide the cover downward to remove.

2) Plug the battery pack connector (red & black wires) into the jack inside the battery compartment (the connector notches fit into the grooves of the jack only one-way). Match the wire colors to

the polarity label in the battery compartment, connect the battery, and listen for a click to insure connection.

3) Make sure you have a good connection by slightly pulling on the

battery wires. If the connection is secure, the battery jack will remain in place.

4) Place the battery case cover back on the handset by sliding it

upwards until it clicks into place. 5) Place the handset in the base unit for 15-20 hours without

interruption. The base unit's LED light (labeled charge) illuminates once the handset is placed in the base. The LED light will illuminate whether the battery pack is connected or not.

If the base charge LED light does not illuminate:

•Check to see if the AC adapter is plugged into the base unit and the electrical wall outlet properly (use only the supplied AC adapter. Do not use any other AC adapter).

•Check to see if the handset is sitting correctly in the base and making good contact with the base unit's charging contacts.

Getting Started [ E 1 1 ]

Image 13

Contents CLT-E30 CLT-E32 CLT-E33 UP383BA0.book Page 86 Thursday, May 26, 2005 1048 AM Contents Welcome FeaturesWelcome/Features/Terminology E Terminology Checking the package contentsControls & Functions E Controls & FunctionsCharge LED Display and Icons Example of the Standby Mode displayDo the following steps Setting up the PhoneChoose the best location Install the rechargeable battery pack into the handset Getting Started E 1 Low battery alert Cleaning the battery charging contacts Connect the base unit Tip Choose the dialing mode Standard wall plate mounting Mounting the Base Unit on a WallDirect wall mounting UP383BA0.book Page 19 Thursday, May 26, 2005 1048 AM About the Menu Options Walkie-Talkie Direct-Link Mode For Multi HandsetsSummary of Main Menu and Submenu Options Room Monitor for multi handsetsSubmenu option Description Handset SetupWell see page E29 Area Code Global SetupReplacing Base System ResetWalkie-Talkie Direct-Link Mode For Multi Handsets Setting Up the MenuUsing the Walkie-Talkie Mode Entering the MenuRoom Monitor For Multi Handsets Using Room Monitor6Q4QQO/QPKVQT Programming your Voice Mail Access Number Handset SetupSelecting a Ringer Tone Distinctive Ringer SetupSetting the Anykey Answer Setting the Automatic TalkSetting the True Banner #PMG#PUYGTSetting Day and Time Setting the Key Touch ToneSelecting a Language .CPIWCIG PinkujSetting the Area Code Setting Cidcw Caller ID on Call WaitingCopy Phonebook For Multi Handsets Setting the Dial Mode8QKEG/CKN6QPG Voice Mail ToneDe-register the Handset Replacing the Base Setting9JKEJ*CPFUGV GIKUVGT*5Making and Receiving Calls Basics6 Basics QNFVQVTCPUHGT Placing a Call on HoldRedialing from Talk Mode Redialing from Standby ModeRedialing a Call Storing a Redial Record Deleting a Redial RecordGNGVG4GFKCN Handset ringer volume Adjusting the Handset Ringer, Earpiece and Speaker VolumeEarpiece and speaker volume Ringer MuteMute Microphone Tone Dialing Switch-overTraveling Out-of-Range Clarity Booster Privacy Mode2TKXCE/QFG1P Find Handset Flash and Call Waiting Dialing your Voice Mail Service Using One Touch Voice Mail AccessVoice Mail Access Phonebook Phonebook5VQTGFKV0COG Qxkgu 5RGGF&KCN 0Q5GNGEVP 52&ORV KUVKPEVKXG4KPI 0Q5GNGEVP NkemgtSteps for Entering Names and Special Characters If you make a mistake while entering a name Viewing the Phonebook From Standby Mode Making Calls Using the PhonebookFrom Talk Mode Editing the Stored Data Speed DialingGNGVG/GOQT Chain DialingCPG5OKVJ Caller ID and Cidcw Caller ID on Call Waiting8 Caller ID Viewing the Caller ID List Deleting Information from the Caller ID List Deleting a Caller ID MessageGNGVG%CNNGT+ GNGVG#NN Deleting all Caller ID names/numbersLong Distance calls and Area Code Setting/Cancellation Storing Caller ID messages in the Phonebook Call Waiting Deluxe Features #PUYGT&TQR #UMVQ*QNF QTYCTF%CNNQTYCTF%CNN %QPHGTGPEG Multi-Handset Expandability Expanding Your PhoneConnecting the Charger 2NCEGJCPFUGV QPOCKPDCUG VQTGIKUVGT Register the Handset to the BaseFor 15-20 hours Walkie-Talkie Call Using the Walkie-Talkie Direct-Link Mode For Multi HandsetsKTGEV.KPM Room Monitor For Multi HandsetsWay Conferencing For Multi Handsets Intercom/Call Transfer Feature For Multi Handsets6QKPVGTEQO IntercomReplacing the Base Call Transfer FeatureChanging the Digital Security Code Additional InformationHeadset Installation Installing the BeltclipTo attach the beltclip To remove the beltclipRecycling Nickel-Metal-Hydride Batteries Battery replacement and handlingSymptom TroubleshootingHandset for 15-20 hours 0 Additional Information Technical Information Important Safety InstructionsTerminal Equipment Sanyo Comfort Warranty Sanyo Canada Inc Original Retail Purchasers ResponsibilitySOS Help Line Sanyo Canada Inc