Sanyo CLT-5812 instruction manual Install the rechargeable battery packs into the handsets

Page 7

UP016DH(CLT5812) ENG OM 3/7/05 5:21 PM Page 5

GETTING STARTED

B. Install the rechargeable battery packs into the handsets

Both handsets are powered by a rechargeable battery packs.

The battery recharges automatically when the handset is placed in the base unit or charging cradle.

IMPORTANT

Use only the Sanyo rechargeable battery pack supplied with your cordless telephone.

Charge the handset battery packs for at least 15-20 hours before

using your new cordless telephone for the first time! To maximize the charge capacity of your battery pack, DO NOT plug the telephone cord into the base unit and wall jack until the battery is fully charged.

1 Press down on the handset battery case cover (use the finger indention for a better grip) and slide the cover downward to remove.

2 Plug the battery pack connector (red & black wires) into the small, black jack inside the battery compartment.

(The connector notches fit into the grooves of the jack only one-way.) Match the wire colors to the polarity label in the battery compartment, connect the battery and listen for a click to ensure connection.

3 Make sure you have a good connection by pulling slightly on the battery wires. If the connection is secure, the battery jack will remain in place.

4 Place the battery case cover back on the handset by sliding it upwards until it clicks into place.

Note:

Red
Black	Red	Black
	Wire	Wire

Place the second handset in the charger with the keypad facing forward for 15-20 hours before use.

E5

Image 7

Contents GHz Introduction FeaturesContents Dual Handsets Controls and functionsCHARGE/IN USE LED Setting up the phone Checking the package contentsGetting Started Install the rechargeable battery packs into the handsets Standby Mode Low battery alertCleaning the battery charging contacts Talk ModeRoute the cord Tip Follow these simple steps to register Before using, register second handset to the base unitTo receive a transfer call from the second handset When to re-register handsetsCall transfer feature To transfer a call to the second handsetStandard wall plate mounting Mounting the base unit on a wallDirect wall mounting Changing your Automatic Talk Auto Talk and Cidcw Setting menu optionsEntering your area code Setting the language Choosing the dialing modeOr Charging Cradle BasicsMaking and receiving calls Handset On BaseTemporarily mute ringer Adjusting the handset ringer and earpiece volumeHandset ringer tone and volume Earpiece volumeRedial Tone dialing switch-overTraveling out-of-range Flash and call waiting Selecting a different channelVoice mail waiting indicator Storing phone numbers and names DirectoryE22 If you make a mistake while entering a name Steps for entering names and special charactersE24 Memory dialing from Talk Mode Memory dialing from Standby ModeMaking calls with memory dialing Chain dialing SELECT/CH key Editing a stored name and/or phone numberE28 ¨Delete MemoryXX?¨ appears Erasing a stored name and phone numberSpeed dial Speed DialStoring and editing the speed dial Deleting the speed dial Making calls with the speed dialCaller ID Caller ID FeaturesWhen the telephone rings You must subscribe to Caller ID service to use this featureViewing the Caller ID message list Deleting a Caller ID message When the pointer is at ¨Yes¨When the pointer is at ¨No¨ Deleting information from the Caller ID listCaller ID Features Long Distance calls and Area Code Setting/Cancellation Using the Caller ID listCalling a party from the Caller ID list Returns to the Caller ID list Storing Caller ID messages in memory dialingTo attach the beltclip Installing the beltclipAdditional Information Changing the digital security codePower Failure Battery replacement and handlingSymptom Suggestion CHARGE/IN TroubleshootingSymptom Suggestion Unavailable Technical Information Important Safety InstructionsSanyo Canada INC.’S Responsibility Sanyo Comfort WarrantyShipping costs of the unit back to Sanyo SOS Help LineUCZZ01016DZ