Away ,FROMTHEBASE Unit, THE-HANDSET does not

IN CASE OF DIFFICULTY

If you have difficulty operating your

YOU GET NOISE, STATIC OR A

"YOU GET -NOISE, STATIC, OR-A

phone, the suggestions below should

WEAK'SIGNALWHEN'WHEN,;,YOUIREYOU'RE

solve

the

problem.

If you still have

AWAY ,FROMTHEBASEUNIT

UNIT. 5 ' 5

difficulty after trying

these suggestions,

You may be' outof

range.

Either

call VTECH Communications

move close to the base, or relocate

1-800-595-9511 in the US. and

VTech

the base unit.

Electronics Canada Ltd at 1-800-267-

The layout of your home may be

7377 in Canada.

limiting the range. Try moving the

base unit to another position.

THE PHONE DOESN'T WORK AT

THE HANDSET DOES NOT RING

ALL

THE-HANDSET DOES NOT

RING

WHEN YOU RECEIVE A CALL

WHEN YOU RECEIVE A CALL.

\ . .-

pugged

Make sure you have the handset

Make sure the telephone line cord is

ringer activated. To set the ringer,

plugged firmly into the base unit and

see "PROGRAMMING

THE

the telephone wall jack.

RINGER".

Make sure the batteries are

Make sure the telephone line

properly charged.

If the

'LOW

cord is plugged firmly into the

BATTERY'message is shown, the

base unit and the telephone jack.

battery pack needs charging.

Make sure the power cord is

;

. .ll,',,l'.,

plugged in.

N.~D,IA.~;T,O.NE.~.;~;~;,;.::.:~~~.~;t:!!:,Jj;-. .,;:<:.a:~,

You may be too far from the base

First check all the suggestions

unit.

above.

You may have too many extension

If you still don'thear a dial tone,

phones on your telephone line to

disconnect the base unit from the

allow all of them to ring.

Try

telephone

jack

and

connect a

unplugging some of the other

different phone.

If there is no dial

phones.

tone on that phone either, the

YOU ,HEAR:OTHER, CALLS WHILE

problem is in your wiring or local

service. Call your local telephone

USING Y0UR:PHONE.S .::

company.

Disconnect'your base unit from

@'4%.rL..\.,:.8>,i.-,"..,-

the telephone jack,

and plug in a

YOU GET NOISE, STATIC OR A

regular telephone.

If you still hear

; ~ ~ ~ ~ ~ G ~ ~ ~ ~ ., O~RI:A~ E , ~ ~ ~ T A T I , c ,

SIGNAL

other calls, the problem is probably

.WEAK~ ; !f~i & @ w AEVENL ~ ,WHENv,N&~W.HE

YOU'RE NEAR THE BASE UNIT

Y&u&$&!@&T~.

;-BASE,.~U.NI~~::~;

in your wiring or local service. Call

Household

appliances plugged

your local telephone company.

into the same'circuit asthe base

YOU HEAR NOISEINTHEHANDSET,

unit

can

sometimes

cause

interference.

Try

moving the

AND NONE .OF THE KEYS OR

appliance or the base unit to

BUlTONS WORK. -

another outlet.

Make sure the power cord is plugged

in.

COMMONCURE FOR ELECTRONIC

EQUIPMENT..,,

Electronics,likepeople,cansometimes get confused. If the unit does not seem to be responding normally, then try putting the handset in the cradle. If it does not seem to respond after trying this a few times, do the following (in the order listed):

1.Disconnectthe power to the base.

2.Disconnect (remove) the handset battery pack.

3.Remove the base unit battery pack, where applicable.

4.Wait a few minutes.

5.Connect power to the base.

6.Install the handset battery pack.

7.Install the base unit battery pack, where applicable.

8.Place the handset in the base unit cradle. If the handset has not been recently charged, allow 8 hours before use.