Telex BTR-1 Local Headset, Start-up, Status Screen, Powering the Base Station

Page 24

TALK LIGHT

ON/OFF

LCD DISPLAY

PEAK INTERCOM

SWITCH

LEVEL LIGHT

 

 

HEADSET VOLUME

 

 

ADJUST

 

 

HEADSET

 

 

CONNECTOR

MENU AND SET

UP AND DOWN

 

MICROPHONE GAIN

BUTTONS

BUTTONS

 

 

 

TALK BUTTON

 

CONTRAST ADJUST

 

 

 

 

 

PEAK AUX LEVEL LIGHT

Figure 6-9

Front Controls and Connector

Local Headset

The local base station headset always following the audio se- lection of the beltpack. It cannot be set to independently select intercom channels.

Volume Control

Turn control clockwise to increase the headphone volume.

Talk Button

Press to enable audio path from the headset microphone. The talk light will activate when the talk button is active This light has two functions. Green indicates activation of the talk button. Red or flashing red on most speech indi- cates overmodulation (too strong of input audio).

Overmodulation:

Light flashes on loudest speech = Gain OK Light flashes on all speech = Gain too High Light never flashes on loud speech = Gain too Low

Start-up

When the BTR-1 is powered-up the 1st screen displayed is the start-up splash screen. It will be displayed for about 3 seconds. This screen contains the software version and channel map versions that are loaded into the base station. The following screen has software version sb10016, and channel map ver- sions B0001 and 30001. This indicates it is a B3 unit.

After 3 seconds the status screen will appear. See the "BTR-1 Menu Structure" section for a flowchart of the main BTR-1 screens.

Status Screen

The status screen is the main information screen of the base station. It displays a number of system items:

Microphone Gain

The microphone gain of the base station’s headset micro- phone maybe adjust via the pot above the Talk button. A plastic screwdriver was provided with the base station for this purpose. Adjust the gain for the overmodulation set- ting as shown above.

Powering the Base Station

The base station requires 12 – 15 Volts AC or DC at 1 Amp for power. The power jack accepts a 5.5 mm x 2.1 mm screw on plug. An inline 12 Volt DC power supply was provided with the base station.

Power the base station via the rocker switch located to the left as facing the base station.

Name of Base Station

Number of Base Station

The Beltpack Button Currently Selected

Group and Channels

Intercoms Active

The Bands of System A2, B3, E7, etc.

The Intercom Type Selected 2W or 4W

Battery Life at the Beltpack

6-5

Image 24
Contents Telex Table of Contents Introduction SpecificationsBTR-1 Base Station TR-1 BeltpackTable of Contents System Features IntroductionGeneral Description Blank BTR-1 Block Diagram BTR-1 Block DiagramTR-1 Block Diagram DSPBTR-1 Base Station Controls and Connections Front PanelControls and Connections Rear Panel BTR-1 Rear PanelTR-1 Beltpack Controls and Connections Top PanelTR-1 Top Panel BAT/O.M. LightTR-1 Rear Panel/Connector/Antennas Push-to-Talk/Push-to-Transmit SwitchHeadset Jack Wiring LCD Liquid Crystal DisplaySpecifications BTR-1TR-1 Specifications Initial Equipment Set-Up UnpackingTR-1 Quantity DescriptionRack Mounting Rack Mounting a Single Base StationRack Mounting Two Base Stations Side-by-Side Antenna Placement Antenna ConnectionAntenna Polarization Distance between AntennasDistance Between base station and beltpack Operating System Near ObstructionsKeeping Site Clear to Antennas Antenna Placement ACS-101Blank BTR-1 Operation Basic Operational DescriptionRX Antenna BTR-1 Rear Connectors Interfacing to the BTR-1 TX / RX Antennas2W Intercom Ports Intercom Assignments of XLR and D-Sub Connetors4W Intercom Ports Auxiliary portRelay Can BusPowering the Base Station Local HeadsetStart-up Status ScreenSystem Settings Encryption CodeBase TX Power BP Off ModeFrequency Settings Intercom TypeIntercom Settings Setting the A, B and C TR-1 button intercom SelectionsChanging Groups / Channels / Frequencies RF Meter ClearScanChanging to the RF Meter Screen ClearScan GroupsSpecial Button Functions Factory Defaults 1st Use DefaultsAlternate Screen LockoutTR-1 Operation System Quick StartControls and Connections Battery Installation Ensure that the On/Off volume control knob is turned offBattery Installation TR-1 Transmit Modes PT TALK, PT TXHeadset Connection SidetoneTR-1 Top Panel Group and Channels Transmit FrequencyEditing Group / Channels Editing the TX Frequency User Groups OnlyBattery Display Receive FrequencyTransmit Power Adjusting the Microphone GainTransmit Power Settings Changing the Transmit Power SettingSerial Number Code Auto ProgrammingSoftware / Channel Map Version Factory Reset Lock Out1st Use Blank TR-1 Menu Structure TR-1 Menu StructureBTR-1 Menu Structure BTR-1 Menu StructureBand Pairing for Systems Available Band PairingsFrequency Bands Band Names and TV ChannelsFactory Group Plan Troubleshooting Problem SolutionBlank Battery Information Battery LifeCold Temperatures and Batteries TR-1Blank Wire Systems Specifications RTSBlank FCC Information FCC LicensingBlank Software License End-User License Agreement for Telex SoftwareBlank Accessories and Replacement Parts MHz Log Periodic Antenna Includes mountingModel No Length Order No Four Slot Smart Charger with Four Nickel Metal HyBlank PN 803959 REV B March Made in U.S.A
Related manuals
Manual 2 pages 14.27 Kb

BTR-1, TR-1 specifications

The Telex TR-1 and BTR-1 represent significant advancements in the realm of professional audio communication, particularly suited for broadcast environments and large-scale live events. Both devices reflect Telex's commitment to innovation and superior functionality.

The Telex TR-1 is a crucial component in wireless intercom systems. It is designed for portable use, featuring a compact and lightweight design that makes it ideal for remote locations and on-the-go communications. The TR-1 utilizes advanced digital signal processing technology, which ensures crystal-clear audio quality and minimal latency, crucial for effective communication in dynamic environments. Its ergonomic design includes intuitive controls, which allow users to adjust volumes and change channels with ease, providing quick access to vital communication functionalities.

One standout feature of the TR-1 is its impressive battery life. The device can operate for extended periods, allowing users to focus on their work without the constant need to recharge. Additionally, the TR-1 incorporates a robust RF performance capability, enabling reliable connectivity over long distances in challenging RF environments, where multiple signals may contest the same frequency spectrum.

On the other hand, the Telex BTR-1 is a versatile base station that complements the TR-1 by providing the backbone for wireless communication in professional settings. The BTR-1 supports multiple channels and can accommodate a variety of belt packs and headsets, making it an ideal choice for complex setups with numerous users. Its 2.4 GHz frequency band means less susceptibility to interference, ensuring that communications remain clear even in crowded situations.

The BTR-1's advanced matrix intercom features allow for flexible routing of audio signals between users, enhancing coordination during productions or events. The unit also includes extensive network capabilities, making it possible to integrate with other communication systems and allowing for remote access and monitoring.

Overall, both the Telex TR-1 and BTR-1 epitomize the blend of portability, reliability, and scalability required for professional audio communications. Their cutting-edge technologies and thoughtful design make them indispensable tools for broadcasters, event organizers, and any professionals who rely on effective and efficient communication solutions.