Alarm Note: Once triggered, the alarm will sound for approximately 40 seconds, or press “Priority Call / Set Button” to turn off alarm. Should no alarm time be needed, do not input any time, allow the dashes to remain, Press “Priority Call / Set Button” to move program mode to the TV input program mode.
TV Input Mode
The TV mode is set with the unit being turned off.
•Press the “Set Button” three (3) times and cause the current TV input, AIR or CABL (“e” not shown on LCD) method to appear on the LCD
*Press the “Volume up / down buttons” to select the desired TV input
*If the CABL mode is chosen, a choice of three (3) modes (LRC, HRC, and STD) must be selected using the “Channel up / down buttons”. STD is normal.
Exit Time / Timer / TV Program Mode
To exit the program mode, the fourth (4) press of the “Priority Call / Set Button” will return the clock displaying the current set time and no longer be in the program mode.
Door Answering
The door call is initiated from the camera or camera(s)
(VSC4R – Recessed in wall or VSC4S – Surface mount) if a second optional camera is installed.
Door call initiated by pressing the button on camera and a chime tone is audibly produced and the monitor display turns on showing the image from the camera.
•No audible communication takes place until homeowner chooses to answer and presses the “Door Button”
•To terminate the call press the “Door Button”
If a second door call is initiated from another camera
•Press the “Door Button” a second time
*The monitor display will switch to the second camera
Door Monitoring
The “Door Button” being pressed will display the activated camera call button that was pressed and the unit must be powered on. Note: Monitoring of the camera location(s) may be performed by
•Pressing the “Door Button” once to activate camera one
•Pressing the “Door Button” a second time activates camera 2, if installed, or will turn off the camera mode if a second
camera is not installed
•Pressing the “Door Button” a third time will turn off the camera mode
Priority Call Use
The “Priority Call / Set Button” is used together with the “Door Button” to disable the microphone at the camera(s) in intercom mode. Normal use would be to cut out unwanted outside noise during conversation heard at the main unit.
•Press the “Door Button”
•Press and hold the “Priority Call / Set Button”
•The camera microphone is disabled so no audio communica- tion will be heard while the “Priority Call / Set Button is active
•Audio and video remain normal at the monitor
•Release the “Priority Call / Set Button” to activate the camera microphone
Record / Play Mode
The record mode is for audio message recording up to a maximum of one (1) minute and the unit must be powered on.
•Press the “Record Button” to activate the recorder
*State your message clearly
•Press the “Record Button” a second (2) time to stop recording
Note: Only one message may be stored. Recording another message will erase the previous recorded message. “rEC” will flash when a message has been stored. Press and hold the “Record Button” for five (5) seconds will erase any recording in memory.
•Press the “Play Button” to initiate the recorded message playback
•Press the “Play Button” a second time to stop the message playback
Telephone Mode
•Press the “Tel Button” to obtain dial tone and activate keypad for telephone operation
•Press the “Tel Button” a second time to terminate the call Note: The telephone is inactive during camera operation
Program Radio Stations
The unit must be powered on. The AM tuning range is from 530Khz to 1710Khz. The FM tuning range us from 87.9Mhz to 107.9 Mhz.
•Press the “AM/FM Button” to turn the radio on and select the desired mode and station to be stored
*Press the “0” button on the keypad to initiate the memory store mode
*Then press a number key 1 – 9 to store the station in
that memory location
Note: The LCD will flash when entering the memory store mode in the FM mode only, not the AM mode.
Radio Use
The unit must be powered on.
•Press the “FM / AM Button” to turn on the last radio mode and station tuned
*If in AM mode, LCD will display AM that is also used for the AM time indicator
*If in FM mode and time is still in AM period, the LCD will
display both AM and FM indicators
•Press the “Channel Up / Down Buttons” to manually tune to desired radio stations
•Press the “Seek Up / Down Buttons” to initiate the “Seek Mode” for the tuner to locate the next radio station
•To stop the “Seek Mode” , Press the “Channel Up / Down Buttons” or select a stored station by using the keypad To recall stored stations:
* Press a number key 1 – 9 that has the desired listening station stored in that memory location
5