Cobra Electronics LI 6500WX owner manual VibrAlert and Call Alert, To change call settings

Page 14

Mode Functions

Operation

During memory location scan (while receiving an Incoming transmission), you can choose from the following:

a. Press and hold the Talk button to communicate on that

 

 

 

 

 

 

 

Introduction

Operation

Customer Assistance

Warranty

 

VibrAlert and Call Alert

•

Your microTALK radio can alert you to incoming signals by sounding an audible call tone, by vibrating silently or both.

memory location.

b. Your radio will remain on that memory location and return to Standby mode. Press the Channel Up or Channel Down button to resume scanning memory locations.

c. After 10 seconds of inactivity, unit starts scan again.

If you press the Talk button while scanning, but more than

10 seconds after receiving a transmission, you will transmit on the memory location on which, during scanning, you last received a transmission.

If you do not press any button within 10 seconds, your radio will automatically resume scanning memory locations.

Mode Button

Channel Buttons

To change call settings:

1.Press the Mode button until the Call Setting icon flashes on the display. The current setting (“01” vibrate + ring, “02” vibrate only or “03” ring only)

is displayed.

2.Press the ChannelUp or ChannelDown button to change the call setting.

3.Choose one of the following:

VibrAlert + Ring

VibrAlert Only

Ring Only

During memory location scan (while not receiving a transmission), you can choose from the following:

a. Press and hold the Talk button to communicate on the channel/privacy code that was displayed before you entered mode functions or memory location on which, during scanning, you last received a transmission.

b. Press the Mode button to proceed to other functions.

c. Press the Lock/Enter button to return to Standby mode on the channel/privacy code that was displayed before you entered mode functions or the memory location on which, during scanning, you last received a transmission.

To reduce the number of memory locations being scanned, you may de-program any unwanted locations. (See page 16 to de-program a memory location.)

a. Press the Mode button to enter the new setting and proceed to other functions.

b. Press the Lock/Enter button to enter the new setting and return to Standby mode.

22

23

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Automated Help Desk Making Life Easier and SaferFor Assistance in the U.S.A Customer Assistance OperatorsLimited One-Year Warranty on Radios & Charger Product Features Warranty and Trademark AcknowledgementFeatures For Products Purchased in the U.S.AEstimated operation time on full charge 12 hours Replace battery compartment cover and belt clipCaring for YourmicroTALKRadio Auto Battery Save Using Your RadioBattery Low For charging microTALK radios in desktop chargerCall Button To alert another person that you are calling To switch from high to medium to low powerListening for a Response To Illuminate DisplayAuto Squelch/Maximum Range Lock FeatureSignal Strength Meter MicroTALK RangePrivacy Codes Mode FunctionsScrolling through Mode Functions Set Ctcss Privacy Codes To select a Ctcss privacy codeSmall numbers flash on the display Through NOAA* All Hazards Radio ChannelsSet DCS Privacy Codes To select a DCS privacy code To listen to All Hazards Radio channelsMemory Locations To turn VOX mode on or offVoice Activated Transmit VOX To set VOX sensitivityTo recall a stored memory channel location Press the Mode button toChoose one of the following DisplayTo scan channels To de-program a memory locationChannel Scan Privacy Code Scan Press the Mode button to proceed to set privacyPress the Channel Up or Channel Down button to Select Channel To scan privacy codesMemory Location Scan To scan memory locationsTo change call settings VibrAlert and Call AlertRoger Beep ConfirmationTone Call ToneSettingsKeystroke Tones Safety Information for microTALK Radios General Specifications FCC LicenseGeneral Specifications Normal PositionFor Products Purchased in the U.S.A Product ServiceProduct Service Questions
Top Page Image Contents