Raymarine RAY 210VHF operation manual Electrical Specifications

Page 15

1.3 SPECIFICATIONS

Appendix 1 : Design Specification Model RAY210

General : FCC Part 80, ITU Radio Regulations Appendix 18. DOC CAT V RSS-18 Issue 2.

1.3.1 Electrical Specifications;

 

Transmitter

 

Channel

51 USA /International

Frequency Stability

+/-5ppm(+/-0.0005%)

Channel Spacing

25KHz Increment

Power Output

25Watts Switchable to 1 Watt

 

into 50 ohm at 13.6 Vdc.

Modulation

Frequency Modulated 16F3

 

(+/-4.5KHz at 1000Hz)

Modulation Audio

within the limit of +/-3dB at

 

6dB/oct freq. curve (300-2.5KHz)

Hum & Noise Level

Greater than 40dB below audio

Audio distortion

less than 10% at 1KHz for +/-

 

3KHz deviation

Spurious & Harmonic

greater than 70dB below carrier

 

power.

Antenna Impedance

50 ohms

Receiver

 

Channel

93 (Includes 10 WX Channels)

Frequency Range

156.025 to 163.275MHz in

 

25KHz increments

Frequency Stability

±5ppm (±0.0005%)

 

–20degree C to +50degree C

Sensitivity

0.3µV for 12dB SINAD

Squelch Sens. Threshold

0.2µV or better

Tight Squelch Sens.

1µV

Adjacent CH Rejection

greater than 70dB

Spurious Image Rejection

greater than 70dB

Intermodulation Rejection

greater than 70dB

Audio Output

4 Watts @ 4 ohms with Less

 

than 10% distortion

Hum & Noise

greater than 40dB

Operating Requirement

 

Input Voltage

13.6 Vdc ±15% (11.6 to 15.6Vdc)

Current Required for

Less than 5.5 A at 25 Watts

Transmit

 

 

Less than 1.3 A at 25 Watts

Operating Temperature

–20º C to +50º C

3

 

Image 15
Contents RAY 210VHF Page Page Page Important Notice PurposePage Table of Contents Page Parts List & Drawings Page VHF Glossary of TermsPage General Equipment FeaturesPage Electrical Specifications SpecificationsMechanical Specifications Unpacking and Inspection Equipment SuppliedDescription Typical Mounting Methods Planning the InstallationOutline and Mounting Dimensions Mounting Options Electrical ConnectionsCable DC Power and External Speaker ConnectionsExternal Speaker Connections Antenna ConnectionsAntenna Mounting Suggestions Grounding Introduction Controls and LCD DisplayControls Page Page Page Page Page Layout of Controls and Connectors LCD Display 0188 Operating Procedures Selecting a Weather Channel To Transmit and Receive on Intl FrequenciesDesign Channel Frequency MHzIntl 3 1st Intermediate Frequency Amplifier Circuit Antenna Switching CircuitReceiving Circuit Operation High Frequency Amplifier CircuitTransmitting Circuit Operation Antenna Monitoring Circuit High Frequency Power Amplifier CircuitPLL Circuit Operation APC CircuitBlock Diagram / RF PCB Block Diagram / CPU PCB How to contact Raymarine Technical Support Accessories and PartsProduct Repair and Service +1 800 539 5539 ext Alignments and Service Preventative MaintenanceTest Equipment PLL Adjustment TRANSMITTER/RECEIVERRF Sensitivity Adjustment Receiver Frequency Adjustment TransmitterModulation Adjustment Transmitter Power Output AdjustmentTrouble Shooting Guide Weather Alert Frequency Adjustment ReceiverMaster Reset Page XTAL1 Section Parts List Description IC1 Description CPU PCB Assembly IC1 IC BR93LC56AF IC2 RAY210 Assembly Drawing Mechanical Parts List Schematic Diagram Schematic diagram/CPU PCBl Schematic diagram/CPU PCB RF PCB Layout Top View RF PCB Layout Rear View CPU PCB Layout Top view CPU PCB Layout Rear View Page VHF Marine Channel Usage Guide and Licensing Requirements Section AppendixPage Usage Guide Emergency Channel Page Coast Guard Navigation Channel Page Channels 24, 25, 26, 27, 28, 84, 85 Weather Channels WX1, WX2, WX3 State Control Environmental ChannelPhonetic Alphabet Page PO3 5TD USA