DVD-K29GCS
8.2.Service Mode Table 1
The service modes can be activated by pressing various button combination on the player and remote control unit.
Player buttons | Remote control unit buttons | Application | Note |
PAUSE | 0 | Displaying the UHF display F_ _ _ | Refer to section 8.3. Self- |
+ |
|
| Diagnosis Function (UHF |
OPEN/CLOSE |
|
| Display). |
| 5 | Jitter check, tilt adjustment | Refer to section 10.4. |
|
| *Display shows J_xxx/yyy_zz | Optical Pickup Tilt |
|
| "yyy" and "zz" shown to the right have nothing to do with the jitter | Adjustment |
|
| value. "yyy" is the error counter, while "zz" is the focus drive |
|
|
| value. |
|
|
| Refer to section 10.4. for Optical Pickup Tilt Adjustment |
|
|
| Procedure. |
|
| 6 | Checking the region numbers and broadcast system |
|
| 7 | Checking the program version | Check the IC8651 FLASH |
|
|
| ROM program. |
| 9 | Lighting Confirmation Function of Display Tube |
|
| FUNCTION | Checking the laser drive current | Refer to section 7 |
|
|
| Optical Pickup |
|
|
| Replacement Procedure. |
| PAUSE | Writing the laser drive current value after replacing the optical |
|
|
| pickup (do not use for anything other than optical pickup |
|
|
| replacement) |
|
PAUSE |
| Initializing the DVD player | Refer to section 8.5. |
QUICK OSD |
| (restoring factory preset settings) | Initializing the DVD |
OPEN/CLOSE |
|
| player. |
8.3.DVD Self Diagnostic Function-Error Code
Error Code | Error Content |
| Additional error explanation | Defect 1 | Defect 2 | Defect 3 | Defect 4 | |||
| U, H error |
|
|
|
|
|
|
|
| |
U11 | Focus error |
|
|
|
|
|
|
|
| |
U15 | Unfinalized |
|
|
|
|
|
|
| ||
H01 | Tray loading error |
|
|
|
|
|
|
| ||
H02 | Spindle servo error |
| (Spindle servo, DV2 (IC8001) SP motor, CLV |
|
|
|
| |||
|
|
|
|
| servo error) |
|
|
|
|
|
H03 | Traverse servo error |
|
|
|
|
|
|
| ||
H04 | Tracking servo error |
|
|
|
|
|
|
| ||
H05 | Seek error |
|
|
|
|
|
|
|
| |
H06 | Power error |
|
| Cannot switch off the power because of the panel |
|
|
|
| ||
|
|
|
|
| and system computer communication error |
|
|
|
| |
H07 | Spindle | motor drive |
|
| Spindle |
|
|
| ||
| error |
|
|
|
|
| motor ass’y |
|
|
|
| DSC related |
|
|
|
|
|
|
| ||
F500 | DSC error |
|
| DV2 (IC8001) stops in the occurence of servo | Optical | DV2 | servo drive |
| ||
|
|
|
|
| error (starup, focus error, etc) |
| pickup | (IC8001) |
|
|
F501 | DSC not Ready |
| DV2 |
|
|
| ||||
|
|
|
|
| (Communication failure caused by idling of DSC) | (IC8001) |
|
|
| |
F502 | DSC Time out error |
| Similar disposal as F500 |
| Optical | DV2 | servo drive |
| ||
|
|
|
|
|
|
| pickup | (IC8001) |
|
|
F503 | DSC | communication | Communication error (result | error occured | DV2 | EEPROM |
|
| ||
| Failure |
|
|
| although communication command was sent) | (IC8001) | (IC8611) |
|
| |
F505 | DSC Attention error |
| Similar disposal as F500 |
| Optical | DV2 | servo drive |
| ||
|
|
|
|
|
|
| pickup | (IC8001) |
|
|
F506 | Invalid media |
| Disc is flipped over, TOC unreadable, | DISC | DV2 |
|
| |||
|
|
|
|
| incompatible disc |
|
| (IC8001) |
|
|
| ODC related |
|
|
|
|
|
|
| ||
F600 | Access |
| failure | to | Operation stopped because navigation data is not | DV2 |
|
|
| |
| management |
| accessible caused by the demodulation defect | (IC8001) |
|
|
| |||
| information | caused | by |
|
|
|
|
|
| |
| demodulation error |
|
|
|
|
|
|
| ||
F601 | Indeterminate sector ID | Operation stopped caused by | the request to | DV2 |
|
|
| |||
| requested |
|
| access abnormal ID data |
| (IC8001) |
|
|
| |
F602 | Access failure to LEAD- | LEAD IN data unreadable |
|
|
|
|
| |||
| IN | caused | by |
|
|
|
|
|
| |
| demodulation error |
|
|
|
|
|
|
| ||
F603 | Access |
| failure | to | Access failure to CSS data of disc |
|
|
|
| |
| KEYDET | caused | by |
|
|
|
|
|
| |
| demodulation error |
|
|
|
|
|
|
| ||
F610 | ODC abnormality |
| No permission for command execution | DV2 |
|
|
| |||
|
|
|
|
|
|
| (IC8001) |
|
|
|
20