Cooper Lighting IMI-685 installation instructions Sheet 2

Page 2

INSTALLATION INSTRUCTIONS

IMPORTANT : READ CAREFULLY BEFORE INSTALLING FIXTURE.

Tribute

Sheet 2 of 4

1/7/08IMI-685

Mounting the fixture

4a. Arm Mount (FIG. 4a)

FIG. 4a (Arm Mount)

Arm Mounting (Square Pole) Lay the fixture on its’ top with door removed. Remove pole cap allowing nut plate to be inserted into pole and align with bolt holes. Install threaded bolts into nut plate. Align arm (end with drain holes towards pole) and place over threaded bolts.

Align holes in fixture with bolts. Route fixture supply leads through arm and into pole. Inside of fixture place lock washer and nuts onto threaded bolts, secure. Housing and arm must be square with pole. Tighten bolts to 30 ft lbs. Bolts must not be extended into fixture more than 1". Finish securing electrical connections inside of pole.

Arm Mounting (Round Pole) Installation is the same as square pole except a round pole adapter is used against the round pole.

4b. Internal Mast Arm Mount (FIG. 4b)

• Loosen the four tenon clamp bolts for insertion of the

mounting tenon. Note: for the 2" pipe size tenon,

remove the tear away portion of the tenon entrance

gasket. To remove, grasp the aluminum gasket with

pliers and twist off the pre-cut portion of the gasket.

• Pull service lead wires through the mounting tenon until

Nut Plate

Arm

Drain Hole

InThis

Location

Pole Cap

Hex Nut

Lock Washer

1/2-13Threaded Rod.

Max. extension into housing

is 1”.

Cross Sectional View of Fixture Mounted to Pole

FIG. 4b (Internal Mast Arm Mount)

about 6" extends beyond the tenon end.

• Slide the luminaire onto the tenon while guiding the

service lead wires. Make sure end of tenon is against

stop in housing.

• Tighten 4 tenon clamp bolts. Note: fixture can be

leveled by tightening front bolts differently than rear

bolts. When fixture is level, torque all 4 clamp bolts to

100 inch-pounds. Tighten bolts in alternating pattern.

• Connect service lead wires to fixture leads and anchor

leads in place so they are not in contact with the reflector

surface or ballast surface.

• Replace electrical compartment cover removed in

step 3.

2” or 1 1/2”

Mounting

Tenon

Flip Clamps

over for 1 1/2” Pipe

Tear off this part of gasket for 2” pipe size

“A”

Service Lead Wires

Extend Min. 6”

Housing

Stop

Electrical

CoverDetail “A”

Tenon Clamp Bolts (qty. 4)

Torque to 100 inch pounds

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest representative.

NOTE: Specifications and dimensions subject to change without notice

Visit our web site at www.cooperlighting.com

Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 ADH070937

Image 2
Contents Tribute Sheet 1Sheet 2 4d. Trunnion Mount d Sheet 308IMI-685 4c. Slipfitter Mount c 08IMI-685 WiringSheet 4

IMI-685 specifications

Cooper Lighting’s IMI-685 is a cutting-edge recessed lighting solution that effortlessly blends aesthetics with high-performance functionality. Designed with versatility and efficiency in mind, the IMI-685 is perfect for a wide variety of applications, including residential, commercial, and institutional spaces.

One of the standout features of the IMI-685 is its innovative LED technology. Utilizing energy-efficient LEDs, this recessed fixture provides excellent illumination while significantly reducing energy consumption compared to traditional lighting options. The IMI-685 boasts a long lifespan, which not only minimizes maintenance costs but also contributes to sustainability efforts by decreasing waste.

The IMI-685 is equipped with a range of lumen output options, ensuring that users can achieve the desired brightness and ambiance for any environment. With adjustable lumens, users can select between different power levels to suit their specific lighting needs. This flexibility is particularly beneficial in spaces where lighting requirements may vary, allowing for tailored solutions.

Another remarkable characteristic of the IMI-685 is its sleek, low-profile design. The fixture seamlessly integrates with various ceiling types, providing a clean and unobtrusive look that complements contemporary architecture. The trim options available allow for further customization, enabling users to match their lighting to existing decor.

The IMI-685 also features advanced dimming capabilities, making it ideal for creating desirable lighting effects in different settings. With compatibility for various control systems, including dimmers and smart home technology, users can easily manage light levels and enhance the mood of their space.

In addition to its aesthetic appeal and flexible performance, the IMI-685 prioritizes safety and compliance with industry standards. The fixture has undergone rigorous testing to ensure it meets or exceeds the necessary safety regulations, providing peace of mind to both installers and end-users.

Overall, Cooper Lighting’s IMI-685 is an exemplary choice for anyone seeking an efficient, versatile, and stylish lighting solution. With its combination of energy efficiency, design flexibility, and smart technology integration, the IMI-685 represents the future of recessed lighting, making it an excellent investment for modern illumination needs.