Uniden EXI 7246 Series manual Liquid Damage, Case Action, Handset, Base

Page 40

Liquid Damage

Moisture and liquid can damage your cordless phone. In case of accidental submersion, please follow these steps.

Case	Action

If the handset or base is exposed to	Wipe off the liquid, and use as normal.
moisture or liquid, but it only affects the
exterior plastic housing.

If moisture or liquid has entered the	Handset:
plastic housing (i.e., liquid can be heard	1.Remove the battery cover and leave it off for ventilation
in the phone or liquid has entered the	2.Remove the battery pack by disconnecting
handset battery compartment or vent	3.Leave the battery cover off and the battery pack disconnected for at least 3 days
openings on the base).	4.Once the handset is completely dry, reconnect the battery pack and the battery cover.
	5.Recharge the handset’s battery pack for 20 hours before using again.
	Base:
	1.Disconnect the AC adapter from the base unit, cutting off electrical power.
	2.Disconnect the telephone cord from the base unit.
	3.Let dry for at least 3 days.
	IMPORTANT: You must unplug the telephone line while recharging the battery pack to
	avoid charge interruption.
	CAUTION:
	DO NOT use a microwave oven to speed up the drying process. This will cause permanent
	damage to the handset, base and the microwave oven.
	After following these steps, if your cordless telephone does not work, please send to:
	Uniden America Corporation
	Parts and Service Division
	4700 Amon Carter Blvd.
	Ft. Worth, TX 76155
	1-800-554-3988, Monday through Friday
	8 a.m. to 5 p.m. CST

[ 3 8 ] A D D I T I O N A L I N F O R M A T I O N

w w w . u n i d e n . c o m

Image 40

Contents Page Page W . u n i d e n . c o m U I C K R E F E R E N C E G U I D E Contents Welcome Features Controls and Functions Terms Used in this Manual Choose the Best Location Installing the PhoneDo the following steps Install the Rechargeable Battery Pack into the Handset Connect the Base Unit and Charge the Handset Use only the suppliedMount the base unit on a wall Standard wall plate mountingInstalling the Beltclip Direct wall mountingHeadset Installation Activating AutoTalk Basic SetupActivating Caller ID on Call Waiting Entering Your Area Code Choosing the Dialing Mode Setting the LanguageSelecting the Ring Tone and Volume Using Your Phone Making and Receiving CallsMaking a call Receiving a callRedialing the last dialed number Adjusting the Earpiece VolumeTemporarily Mute Ringer Traveling Out-of-Range Tone Dialing Switch-overSelecting a Different Channel Using Call Waiting Find HandsetVoice Mail Waiting Indicator RocketDial Storing the RocketDialUsing the Speed Dial Memory Storing Names and Numbers in Speed Dial MemoryIf you make a mistake while entering a name W . u n i d e n . c o m Storing Caller ID messages in Speed Memory Locations To cancel speed dialing Making Calls from Speed Dial MemoryWhen the Telephone Rings Caller ID and Cidcw Caller ID on Call WaitingViewing the Caller ID Message List L L E R I D F E a T U R E S 2Deleting a Caller ID message Deleting Information from the Caller ID ListDeleting all Caller ID names/numbers Making a Call from the Caller ID List Changing the Digital Security Code Battery replacement and handling Low battery alertPower Failure Cleaning the battery charging contacts General Information FrequencyTroubleshooting Symptom SuggestionAppliances Liquid Damage Case ActionHandset BaseImportant Safety Instructions Important Electrical ConsiderationsInstallation Considerations One Year Limited WarrantyTerminal Equipment Radio Equipment Index G, H, I, J, K, LMemory List Memo Please do not Return this Product to the Place of Purchase Register Online Today