Uniden EXAI8580 manual Using Your Phone

3-4. Setting the Ringer Tone (RINGER)

1)With the phone in standby, press and hold [cid/menu].

2)Press [select/channel] to rotate through the four available ring tones (A, B, C, and D). As you switch to the next ring tone, the handset sounds a sample of that ringer.

3)When you hear the ringer you want, use [/ ] and [] to move the pointer to another menu item.

OR

If you’re finished, press [END] to return the handset to standby.

The handset will use the new ring tone starting with the next incoming call.

3-5. Setting the Ringer Volume

On the handset (RING.VOL.)

1)With the phone in standby, press and hold [cid/menu].

2)Press [] to move the pointer to RING VOL.

3)Press [select/channel] to rotate through the three available volume levels (HIGH, LOW, and OFF). As you switch to the next volume level, the handset sounds a sample of the current ring tone at that level.

4)When you hear the volume level you want, use [/ ] and [] to move the pointer to another menu item.

OR

If you’re finished, press [END] to return the handset to standby.

The handset will use the new ringer volume starting with the next incoming call.

Note: If you set the ring volume to OFF, the handset won’t ring. The base will ring according to its ringer settings.

On the base

You can change the base ringer volume with the phone in standby or while the phone is already ringing.

1)On the base, press [ringer]. The message counter display shows the current volume level (Hi = high, Lo = low, OF = off) and sounds the ringer at that level. If the volume level is off, the voice prompt announces “Ringer off.”

2)Press [ringer] immediately to switch to the next volume level. As you switch to the next volume level, the base sounds the ringer at that level and shows that level in the message counter display.

3)When you hear the ringer volume level you want to use, stop pressing [ringer].

Note: If you turn the ringer volume off, the base won’t ring. The handset will ring according to its ringer settings.

4) Using Your Phone

4-1. Making and Receiving Calls

		...from the handset		...from the handset speaker phone
	1)	Pick up the handset.	1)	Pick up the handset.
	2)	Press [TALK/flash].	2)	Press [	].
	3)	Listen for the dial tone.	3)	Listen for the dial tone.
To make a call...	4)	Dial the number.	4)	Dial the number.
		OR		OR
	1)	Pick up the handset.	1)	Pick up the handset.
	2)	Dial the number.	2)	Dial the number.
	3)	Press [TALK/flash].	3)	Press [	].

1)Pick up the handset. (If AutoTalk is on, the phone automatically

To answer a	answers when you pick it up from	1) Pick up the handset.
	the cradle.)
call...		2) Press [	].
	2) Press [TALK/flash]. (If Auto Talk is
	on, you can also press any key on
	the twelve-key dial pad.)
To hang up...	Press [END] or return the handset to the cradle.

4-2. Switching a Call to the Handset Speakerphone

To switch a normal call to the speakerphone, press [ ] on the handset. To switch back to a normal call, press

[ ] again.

4-3. Redialing the Last Dialed Number

1)	Pick up the handset from the cradle.			1)	Pick up the handset from the cradle.
2)	Press [redial/pause].		OR	2)	Press [TALK/flash] or [	].
3)	Press [TALK/flash] or [	].		3)	Listen for the dial tone.
				4)	Press [redial/pause].

4-4. Adjusting the Speaker Volume

You can change the speaker volume on the base, the handset earpiece, or the handset speakerphone.

On the base

You can choose from ten volume levels ( - ) for the base speaker. Press [vol/select/] to make the volume louder or [vol/select/] to make it softer .

Notes:

•You can't change the speaker volume when you're using the base setup menu. Exit the menu, and then change the volume.

•If you hear three quick error beeps, it means the speaker is already at the lowest ( ) or highest ( ) volume level.

On the handset

When you are on a normal call, press [/] to make the earpiece louder or [] to make it softer. The handset display shows the current volume level for the earpiece.

When you are using the speakerphone, use [/] or [] to change the speaker volume. The handset display shows the current volume level for the handset speakerphone.

There are four volume levels: LOW, MEDIUM, HIGH, and MAXIMUM. Notes:

•The handset earpiece and the handset speakerphone have separate volume settings.

•If you hear three quick error beeps, it means the earpiece or speaker is already at the lowest (LOW) or highest (MAXIMUM) volume level.