Uniden EXI3226 manual Liquid Damage, Case Action

Page 49

Liquid Damage

Moisture and liquid can damage your cordless phone. In case of accidental submersion, please read the following steps.

Case

 

Action

If the handset or base is exposed

Wipe off the liquid and use as normal.

to moisture or liquid, but only

 

 

affects the exterior plastic housing.

 

 

 

 

If moisture or liquid has entered

Handset:

the plastic-housing (i.e. liquid can

1.

Remove the battery cover and leave it off for ventilation.

be heard in the phone or liquid

2.

Remove the battery pack by disconnecting.

has entered the handset battery

3.

Leave the battery cover off and the battery pack disconnected for at least 3 days.

compartment or vent openings on

4.

Once completely dry, reconnect the battery pack and the battery cover.

the base).

5.

Recharge the handset’s battery pack for 20 hours on the base unit before using

 

 

the phone.

Base:

1.Disconnect the AC adapter from the base unit, cutting off electrical power.

2.Disconnect the telephone cord from the base unit.

3.Let dry for at least 3 days.

IMPORTANT: You must unplug the telephone line while recharging the battery pack to avoid charge interruption.

CAUTION:

DO NOT use a microwave oven to speed up the drying process. This will cause permanent damage to the handset, base and the microwave oven.

After following these steps, if your cordless telephone does not work, please send to: Uniden America Corporation

Parts and Service Division 4700 Amon Carter Blvd. Ft. Worth, TX 76155

1-800-554-3988. Monday through Friday 8 a.m. to 5 p.m. CST

www.uniden.com

A D D I T I O N A L I N F O R M AT I O N [ 49 ]

A D D I T I O N A L I N F O R M AT I O N

Image 49
Contents Page Page To Change Caller ID Options To Choose the Language Contents Welcome Features Controls and Functions 41 42 43 44 Do the following steps Setting up the PhoneGetting Started Install the rechargeable battery pack into the handsetLow battery alert Battery use time per chargeCleaning the charging contacts Connect the base unit For 2 line subscriptions Mounting the Base Unit on a Wall Setting the handset retainer clip for wall mountingStandard wall plate mounting Direct wall mounting To change your AutoTalk and Cidcw Setting Menu OptionsChoosing the dialing mode Int’c or To Enter Your Area CodePress select/vol/ring Setting the language Basic 2-line operation Making and Receiving CallsRinger volume Adjusting the Ringer and Earpiece/Speaker VolumeEarpiece volume Base ringer volumeRedial Tone Dialing Switch-overTraveling Out-of-Range TipSelecting a Different Channel Using the Page FeatureFlash and Call Waiting Answering a Call from the Base Using the SpeakerphoneAnswering a Call from the Handset Dialing from Standby Mode Dialing from Talk ModeMaking a Call from the Base Making a Call from the HandsetPlacing a Call on Hold Using the Speakerphone Mute FeatureExtension In Use Line OperationWay Conferencing Press intercom on the base to contact the handset Press hold. The line 1 and line 2 LEDs flash redPaging from the base to handset Using Your EXI3226 intercomPaging from the handset to base Press intercom/ /int’c Transferring CallsWith the handset Storing Phone Numbers and NamesWith the base If you make a mistake while entering a name Steps for Entering Names and Special CharactersSelect/vol/ring Press line 1 or line 2. The number dials Making Calls with Memory DialingPress line 1 or line Editing a Stored Name and/or Phone Number Chain DialingPress select/vol/ring. The display Press select/vol/ring or delete/flash Erasing a Stored Name and Phone NumberWith the base Caller ID When the Telephone RingsPress cid/menu/hold Viewing the Caller ID Message ListConf Long Distance calls and Area Cord Setting/CancellationInt’c Storing a Caller ID number in a memory location Deleting a Caller ID message Deleting Information from the Caller ID ListPress delete/flash Deleting all Caller ID name/numbers Using Cidcw Caller ID on Call WaitingChanging the Digital Security Code Headset Installation Installing the BeltclipTo attach the beltclip To remove the beltclipBattery replacement and handling MaintenancePower Failure When the handset or base unit becomes slightly dirtySymptom Suggestion Charge/in use LED won’t TroubleshootingCase Action Liquid DamageGeneral Information Battery InformationAC Adapter Information Precautions Installation Considerations Terminal Equipment Radio Equipment Industrial Canada InformationK, L IndexPlease do not Return this Product to the Place of Purchase At Uniden, we’ll take care of you