Uniden UND1685 manual Installing a Line Filter or DSL Filter, Liquid Damage, Resetting Stations

Page 20

Installing a Line Filter or DSL Filter

A telephone line filter or DSL filter prevents services that use the phone line from causing interference on your phone. To get a line filter, contact your service provider or look in an electronics store.

Plug the filter into the telephone wall jack and plug the base into the filter. Make a test call to make sure the noise is gone.

Liquid Damage

CAUTION: If the base is covered in liquid, disconnect the adapter & phone cord from the wall before touching it.

If the liquid is only on the exterior housing of the base or handset, wipe it off and use as normal. If you can hear liquid inside the housing:

1.Remove all compartment covers, and disconnect all cables and cords.

2.If liquid is leaking from any vent or hole, turn the phone so that the vent faces down. If not, place the largest vent face down.

3.Let dry for at least 3 days. Check for liquid inside the phone before replacing compartment covers & reconnecting cords.

Resetting Stations

Unplug the base to reset it. Plug it back in after at least a minute.

If you have trouble with a handset or if you want to replace one, reset it.

1.Press & hold END and # at the same time until you see the System Reset menu.

2.If you still have the base the handset is registered to, select Deregister HS, then select the handset you want to reset. If you don’t have that base anymore, select Base Unavailable.

3.To confirm, select Yes. The handset displays Handset not registered.

Registering Handsets

If you see Not Registered on a handset, you must register it to a base before use.

1.Place the handset in the base; the display should say Registering. If the handset does not fit in the base, open the base menu and select Register Accy. On the handset, press and hold # until Registering displays.

2.Wait until the display says Registration Complete (about 30 seconds), then pick up the handset and press TALK/FLASH.

#If you don’t hear a dial tone or the display says Registration Failed,#

charge the battery completely, then try again.

English - 20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents D1685 Series Users Guide Whats in the box?You will also find If You Contact Uniden’s Phone NumberImportant Safety Instructions What’s in the manual?Installing Your Phone Getting StartedGetting to Know Your Phone Parts of the BaseXx In standby increase the ringer volume Xx When entering text move the cursor to the rightXx In standby decrease the ringer volume Xx During a call switch to a waiting callParts of the Handset Reading the Display On the BaseIcon Handset Only IconsUsing the Menus Basic Menu OperationMenu Functions Menu Option What it doesUsing Your Phone Register Accy. Menu Base OnlyEntering Text on Your Phone From Base From Handset Speakerphone EarpieceChanging the Volume Using the Caller ID and Redial ListsAdding Phonebook Entries Using Call WaitingUsing the Phonebook Using Special Features Silent ModeMultistation Features Phone exits silent modePrivacy Mode Call TransferIntercom From the base From a cordless handsetSetting Up Chain Dialing Using Chain DialingChain Dialing Voice Message NotificationRecording the Outgoing Message Using the Answering SystemAnswering System Options Ans. Setup Accessing the Answering System Getting Your MessagesFollow these steps from the base or a handset From the base From a handsetProgramming a Security Code Using the System While Youre Away from HomeScreening Your Calls Solving Problems Important InformationSystem hangs up and returns to StandbyMultistation problems Possible solutions Answering system problems Possible solutionsInstalling a Line Filter or DSL Filter Resetting StationsCharge the battery completely, then try again Liquid DamageAdapter and Battery Infor- mation Rechargeable Battery WarningBattery pack with normal use FCC Part 68 InformationFCC Part 15 Information Industry Canada I.C. Notice FCC RF Exposure InformationStar is a U.S. registered mark
Top Page Image Contents