Basic Operations, Adjusting the tone | Clarion DXZ745MP specs

Basic Operations

Notes:

•The volume changes each time the ADF setting is switched. Turn down the volume and the sub- woofer volume before performing a switching op- eration.

•Sufficient effects cannot be obtained with some speaker systems. In such cases, adjust the vol- ume.

Adjusting the tone

Press the [A-M] button and select the item to adjust. Each time you press the [A-M] button, the item changes in the following order:

●When the ADF-1 (ADF-2, ADF-3) is set

“SUB-W VOL” ➜ “BALANCE” ➜ “FADER” ➜ Last function mode...

●When the ADF-OFF is set

“SUB-W VOL” ➜ “BASSÅGAINÎ” ➜

“TREBÅGAINÎ” ➜ “BALANCE” ➜ “FADER”

➜Last function mode…

If subwoofer function is set “ON”, “SUB-W VOL” can be selected.

Adjusting the subwoofer output volume

You can adjust the volume output from the unit’s subwoofer output terminal.

1.Press the [A-M] button and select “SUB-W VOL”.

2.Turning the [ROTARY] knob clockwise increases the output volume; turning it counterclockwise decreases the output volume.

The factory default setting is “0”. (Setting range: –6 to 6)

3.When the adjustment is complete, press the [A-M] button several times until the function mode is reached.

Adjusting the bass

The bass gain, bass FREQ (center frequency) and bass Q can be adjusted as follows.

1.Press the [A-M] button and select “BASS

ÅGAINÎ”.

2.Press the [a] or [d] button and select from “BASS ÅGAINÎ” ➜ “BASS Å FREQ Î” ➜ “BASS Å Q Î” ➜ “BASS ÅGAINÎ”…

3.Turn the [ROTARY] knob clockwise or counterclockwise as needed and adjust the gain, the FREQ (center frequency) and the Q.

BASS GAIN : –6 to 8 (The factory default setting is “0”)

BASS FREQ : 50Hz/80Hz/120Hz (The factory default setting is “50”)

BASS Q : 1/1.25/1.5/2 (The factory default setting is “1”)

4.When the adjustment is complete, press the [A-M] button several times until the function mode is reached.

Adjusting the treble

The treble gain and treble FREQ (center frequency) can be adjusted as follows.

1.Press the [A-M] button and select “TREB

ÅGAINÎ”.

2.Press the [a] or [d] button and select from “TREB ÅGAINÎ” ➜ “TREB Å FREQ Î” ➜ “TREB ÅGAINÎ”...

3.Turn the [ROTARY] knob clockwise or counterclockwise as needed and adjust the gain and the FREQ (center frequency).

TREB GAIN : –6 to 6 (The factory default setting is “0”)

TREB FREQ : 8KHz/12KHz (The factory default setting is “12K”)

4.When the adjustment is complete, press the [A-M] button several times until the function mode is reached.

Adjusting the balance

1.Press the [A-M] button and select “BAL- ANCE”.

2.Turning the [ROTARY] knob clockwise emphasizes the sound from the right speaker; turning it counterclockwise emphasizes the sound from the left speaker.

The factory default setting is “0”. (Adjustment range: L13 to R13)

3.When the adjustment is complete, press the [A-M] button several times until the function mode is reached.

Adjusting the fader

1.Press the [A-M] button and select “FADER”.

2.Turning the [ROTARY] knob clockwise emphasizes the sound from the front speakers; turning it counterclockwise emphasizes the sound from the rear speakers.

English

DXZ745MP 13