Troubleshooting
Symptom | Possible Problem | Solution | |
iP98 does not turn on | AC adaptor isn't plugged into a working wall | Plug the AC adaptor into a working wall socket and plug the connector | |
| socket or not plugged into the power supply | into the supply jack on the unit | |
| jack on back of the unit |
| |
iP98 doesn’t respond | iP98 requires a reset | If unit is plugged in and doesn't respond, try resetting the unit by | |
|
| following these steps: | |
|
| a) remove iPhone/iPod from dock | |
|
| b) unplug unit from power source | |
|
| c) remove back up batteries | |
|
| d) wait 1 hour, then resume use | |
| iPhone/iPod is not docked properly | Remove your iPhone/iPod from the dock and check for obstruction on | |
|
| the connectors in the dock and on your iPhone/iPod. Then reseat it in | |
|
| the dock. | |
|
|
| |
Battery Low icon | Batteries are weak | Replace with new batteries | |
always flashing |
|
| |
Batteries were not installed properly | Check to make sure the polarity ( + and – ends) matches the diagram | ||
| |||
|
| in the battery compartment | |
iPhone/iPod does not | iPhone/iPod is not docked properly | Remove your iPhone/iPod from the dock and check for obstruction on | |
respond to the unit/iPod |
| the connectors in the dock and on your iPhone/iPod. Then reseat it in | |
is playing but no sound |
| the dock. | |
comes out | Your iPhone/iPod software is too old | Upgrade software on your iPhone/iPod. For details visit | |
| |||
|
| http://www.apple.com or use iTunes on your computer | |
| iPhone/iPod is locked up/plays but no sound | Check the volume setting. Make sure your iPhone/iPod is working | |
| comes out | properly before docking into the unit. Please refer to your | |
|
| iPhone/iPod manual for details. See above for software upgrade | |
|
| information. | |
|
| You may need to reset your iPhone/iPod. Refer to your iPhone | |
|
| or iPod user guide for details on how to perform a reset. | |
|
|
| |
| Using 1st or 2nd generation iPod, iPod Shuffle or | iP98 cannot control those iPod models or other devices. | |
| other devices. |
| |
Remote Control didn’t | Battery weak | Replace current battery with new battery | |
work | Remote Control is out of range of the iP98 | Move within 30 feet of the unit. | |
| |||
| remote sensor |
| |
iP98/iPhone/iPod | The iP98 is reacting to external interference | Move unit away from potential sources of external interference such as | |
performance is erratic |
| computers, modems, wireless devices (routers) or fluorescent light. | |
|
|
| |
No sound from iP98 | Volume is set too low on iP98 | Make sure volume is turned up | |
iPhone/iPod didn’t | iPhone/iPod is not installed properly | Remove your iPhone/iPod from the dock and check for obstruction on | |
charge up |
| the connectors in the dock and on your iPhone/iPod. Then reseat it in | |
|
| the dock. | |
| iPhone/iPod is locked up/ frozen | Please make sure your iPhone/iPod is working properly before docking | |
|
| into the unit. Please refer to your iPhone/iPod manual for details. | |
| iPhone/iPod battery has problem | ||
|
| ||
No AM band radio | AM loop antenna is not connected to the unit | Plug the AM loop antenna connector to the jack on the back of the unit | |
sound but others OK |
|
| |
AM band radio is very | AM loop antenna isn’t located properly | Move the AM loop antenna away from the main unit AC adaptor and | |
noisy |
| rotate it for best reception | |
|
|
|
7