PYLE Audio PDCD940MP manual Pitch Control Slider, SAM. Button, Track Button, Hot-Cue, BPM Button

10. PITCH CONTROL SLIDER

To match the choices of playback speed (8%, 16%, 32%, 100%), you can choose what range you want between minimum (up side) and maximum (bottom side) by moving the pitch control slider.

11. SAM. BUTTON

Sampler is a kind of sound effect that you record the music from the track. While playing the music, you can use the sampler to mix with music. The maximum length is 8 seconds.

1.Set start point: Press the MEMO key, and then press SAM button, after memorizing the SAM button flashes quickly (2 times in 1 sec)

2.Set End point: Press the SAM button again, when the end point is memorized, the SAM button lights up (not flash).

3.Play Sampler: During PLAY mode, press the SAM button, then the button will flash slowly. (1 time in 1 sec)

12.TRACK BUTTON

These buttons select the track to be played.

13. +10 BUTTON

Press the button to forward 10 tracks. If you forward 10 tracks, and the tracks over total tracks, the unit will jump to track 1...

between PLAY and PAUSE modes.

14. HOT-CUE

This unit will allow you to play from 3 cue points instantly. a. Set CUE memory: Press the MEMO button first, and then press the CUE button to complete the CUE setting, then this CUE button will light up.

b. Play” CUE” memory: Upon pressing specific CUE button, it will flash about 5 seconds.

Note: This function is not available during perform REVERSE sound effect.

15. BPM BUTTON

You can get the BPM number automatically or manually. Pressing the BPM BUTTON for 3 seconds to switch between auto and manual control. The BEAT will be shown on the display! Under the manual mode, tapping this button to get the beat value.

16. PLAY/ PAUSE BUTTON

Each press of this button causes the operation to change between PLAY and PAUSE modes.

17. CUE BUTTON

The cue function allows the CD returning to the memorized point. In PAUSE mode, pressing the CUE button to set the cue point, and the CUE button blinks; in PLAY mode, press this button to pause the unit at the memorized point

18. BOP BUTTON

*Speed Control (SEARCH indicator off)

Rotating the wheel, in play mode, will change the playback speed accordingly. While rotating clockwise, the player speed increase; rotating counterclockwise, the speed decrease.

*Search (SEARCH indicator lights)

Rotating the wheel, the player will forward or backward quickly. The searching speed changed according to the dialing speed. It can be carried out by one frame increment.

The searching speed changed according to the dialing speed. It can be carried out by one frame increment.

21. SEARCH BUTTON

Pressed the button to switch the function of Jog Dial between SEARCH and PITCH BEND.

zWhen the indicator LED is light, dial the jog for quick search forward and backward.

zWhen the indicator LED is off, dial the jog for pitch bend function.

zIf the jog is unmoved for 8 seconds, the indicator is off, and the jog is for pitch bend function.

22.SOUND EFFECT

REVERSE: The music is playing backward. This sound effect can be performed independently, or in parallel with other effect. SCRATCH: Move the JOG Wheel backward or forward like scratching a turntable record. This sound effect can be performed independently, or in parallel with other effect.

23. CONNECTOR PORT

The 8-pin(6-pin) termination permits the connection of the control unit to the main unit.

24.SLEEP:

Leave the unit unused for 30 minutes; the machine will shut off automatically.

The playback will automatically play from the CUE point upon the button is pressed.

19. Seamless Loop (2 sets)

There is A, B/LOOP/ EXIT, RELOOP buttons.

i.. A BUTTON---“start point” (A point. Also, Cue 1 could be A point) After setting up the A point, the red Led light up

ii.. B/LOOP/ EXIT BUTTON: ---“ End point”(B point). Press the B /LOOP button to set up the B point and start the loop playback automatically. Loop lights on the display and the 3 LEDs flash. Press this button again to exit the LOOP playback.

iii.. Return to the loop playback by pressing the RELOOP while in performance. However, if your want to return to loop playback, you can press RELOOP BUTTON

iv.. Change “ START POINT” and” END POINT” by pressing the A& B/ LOOP/ EXIT button again

v.. The interval between A and B point must be more than 20 frames; otherwise, the B point will be canceled, then LOOP function disappear and LOOP fades on the display

20. JOG WHEEL

- 5 -