Nady Systems PSS-150 Installation, CONTeNTS, Mixer Section, Speakers and Stands, Inputs

Page 4

Installation

To ensure years of enjoyment from your NADY AUDIO PSS- 150 Portable Sound System, please read and understand this manual thoroughly before using the unit.

1. INSPeCTION

Your NADY AUDIO PSS-150 Portable Sound System was carefully packed at the factory in packaging designed to protect the units in shipment. Before installing and using your unit, carefully examine the packaging and all contents for any signs of physical damage that may have occurred in transit.

[Please note: Nady Systems is not responsible for shipping damage. If your unit is damaged, do not return to NADY, but notify your dealer and the shipping company (if shipped to you) immediately to make a claim. Such claims must be made by the consignee in a timely manner.]

CONTeNTS:

PSS-150 Mixer Section

PSS-150 Left Speaker

PSS-150 �ight Speaker

(2x) Speaker Stands

(2x) 2 30’ Speaker Cables

SP-1 Starpower™ Microphone

XC-20 20’ Microphone Cable

AC cord

Instruction Manual

Warranty Card

2. SeTUP

After transporting the PSS-150 to the desired location, lay the unit down on its flat side. Unclasp the side panel latches by pulling up on the yellow tab to release and unhook the latch. Carefully lift off the speakers and then remove the speaker stands and accessories from inside the unit.

Mixer Section

Position the PSS-150 mixer section on its flat surface with the control panel facing up. Parts of the unit can become very warm during use. This is normal during operation. Care should be taken to ensure that there is enough space behind the Mixer Section for cooling. Also, do not place the Portable Sound System on high temperature devices such as power amplifiers, etc., or the unit may overheat in operation.

Although the PSS-150 is shielded against radio frequency (�F) and electromagnetic interference (EMI), extremely high fields of �F and EMI should be avoided.

Please make sure that the power unit supplied is marked for the correct voltage in your area (120VAC/60 Hz or 230VAC/50 Hz). Power requirements for electrical equipment differ from area to area. In new installations and portable sound systems, or any situation in which the AC power is in question, it is wise to confirm the voltage and use the appropriate power supply unit before connecting it to power sources.

europe (except UK): 230V, 50Hz

UK and Australia: 240V, 50Hz

USA and Canada: 120V, 60 Hz

For other areas, please check with local authorities.

Speakers and Stands

Fully extend the speaker stand tripod legs and tighten the base thumbscrew. Extend the pole of the stand to the desired height and insert the safety pin completely through the stand hole above the pole thumbscrew. Lower the pole so that the pin rests on the holder and tighten the pole thumbscrew.

Setup the stands on a flat surface where the speakers will be located and not disturbed. Place the speakers on the stands and position them as desired. Note: facing the speakers towards any of the microphones connected with the PSS-150 will increase the chance of feedback.

Connect the speaker cables to the input jacks on the lower left front panel of both the Left and �ight speakers. Connect the other end of each cable to the corresponding Left and �ight speaker outputs on the rear panel of the PSS-150 mixer section. Position the length of the cables so they will not be a safety hazard to people.

WARNING: Connect only the supplied speakers to the PSS-150. Never connect additional speakers to the PSS-150.

Inputs

Connect all sound sources to the appropriate inputs i.e., microphones, keyboards, CD players, karaoke machines. The supplied SP-1 Starpower™ microphone is an all-purpose professional stage and recording microphone with rugged metal construction and excellent clear, transparent sound across the spectrum.

When ready to operate, plug the AC cord into the power source. Make sure that the unit is turned off before connecting to the AC power source to avoid possible loud transients which can damage your speakers or your ears. Before turning on, connect up the speakers and all inputs and outputs desired and turn down the Master Volume.

4

Image 4
Contents PSS-150 Contents FeaturesPage Installation CONTeNTSMixer Section Speakers and StandsFront Panel Controls & Connections DSP Effects Display AUX RCA OutputsSpecifications Rear Panel Controls & ConnectionsMAX Gain DistortionService For Your Nady Audio Product