Nordyne M1G, M1B, M1S, M1M owner manual Flue GAS Sampling, Lighting and Shutdown, GENERAL-ALL Models

Page 20

15. FLUE GAS SAMPLING

It may be necessary to take flue gas sampling from oil and gas gun furnaces (M1S and M1B Series Models) in order to check the perfor- mance after furnace installation. A flue gas sample may be taken from the heat exchanger, which is located behind the hole of the top-front of blower compartment.

1.STOP! Read the SAFETY INFORMATION.

2.Turn off all electric power to the appliance.

3.Remove the black plastic cap located above the blower and save.

4.Through the top of the blower compartment hole, drill a hole for your sampling tube into the heat exchanger.

5.Insert sampling tube through the drilled hole.

6.After a complete check and adjustment of furnace performance, fill the drilled hole with a screw that is larger than the hole.

7.Put silicon sealant (rated at least 500° F) around the screw.

8.Plug the outside hole with the plastic cap you removed in step 3.

!WARNING:

If you do not follow these instructions exactly, a fire or explosion may result causing personal injury, loss of life, or property damage.

16. LIGHTING AND SHUTDOWN

GENERAL-ALL MODELS

Read the safety information on the front page of these installation instructions before lighting furnace. DO NOT ATTEMPT TO LIGHT

FURNACE IF YOU SMELL GAS.

SAFETY INFORMATION

FOR YOUR SAFETY READ BEFORE LIGHT- ING.

a. The first lighting of the furnace after any home setup must be performed by a qualified service technician.

b.If this appliance has a pilot that must be lit by hand, follow these instructions exactly.

c.BEFORE LIGHTING smell all around the furnace for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

d. WHAT TO DO IF YOU SMELL GAS: Do not try to light any appliance. Do not touch any electric switch and do not use any phone in your building. Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. If you cannot reach your gas supplier, call the fire depart- ment.

e.Use only your hand to push in the gas control lever. Never use tools. If the lever will not push in by hand, don’t try to repair it. Call a qualified service technician. Force or at- tempted repair may result in a fire or explo- sion.

f.Do not use this furnace if any part has been under water. Immediately call a qualified service technician to inspect the furnace and to replace any part of the gas valve or control system which has been under water.

LIGHTING INSTRUCTIONS FOR STAND- ING PILOT MODELS.

a. Stop! Read the safety information.

b. Set the thermostat to the lowest setting. c. Turn off all electric power to the appliance. d. Push in the gas control lever slightly and

move left to “OFF.” DO NOT FORCE.

e. Wait ten (10) minutes to clear out any gas. If you then smell gas, STOP! Follow step “d” in the SAFETY INFORMATION. If you don’t smell gas, go to the next step.

f.Find pilot - follow metal tube (pilot tube) from gas control valve. Open hinged fire obser- vation door. The pilot is found at the end of the pilot tube just left of the pilot shield.

g.Slightly depress the gas control lever and move it right to the “ON” position and release; then move it to the “PILOT” position.

h.Move the control lever to “SET” and hold. Immediately light the pilot with a match. Continue to hold the control lever for about one (1) minute after the pilot is lit. Release the lever and it will spring back to the “PILOT” position. Pilot should remain lit. If it goes out, repeat steps “d” through “h” above. If the lever does not spring back when released, stop and immediately call your service tech- nician or gas supplier. If the pilot will not stay lit after several tries, move the gas control lever to “OFF” and call your service techni- cian or gas supplier.

i.Move the gas control lever left to “ON”.

j.Turn on all electric power to the furnace. Set the thermostat to “Heat” and/or the desired temperature setting. Set the On-Off-Fan switch to “ON”.

k.Replace the furnace door.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Leave These Instructions with the Homeowner Table of Contents B 056 a B WSpecifications MANUFACTURERWARRANTY, OWNER’S ResponsibilitiesOwner Information about Your Central Furnace System General DescriptionM1 Furnace Specifications NatInstallation Standards Field Installation Blower AssembliesCould cause unsafe operation, explo You feel that the furnace is not operUnit Location Minimum ClearancesReturn AIR Provisions Minimum ClearancesAll Weather Roof Jack Assemblies 27 45AIR Distribution Systems Roof Jack SelectionApplication Notes Slant Deck FlashingsDuct Connector Selection Platinum Series NON-PLATINUM SeriesCloset or Alcove Non-Platinum Series InstallationCUT OUT Floor Opening & Fuel Line Hole Alternate Attachment Methods Install Furnace Install Roof JackManufactured Home Site Installation of TRANSIT- Mode Venting SystemManufactured Home Factory Connect Thermostat Wires Electrical WiringConnect Power Supply Wires Fuel Piping Control Panel All ModelsThermostat Wire Gauge Typical Gas PipingTypical Oil Piping for Above Ground Single-Line Supply Fuel Oil Type Hook-Up Procedure See FigureHow to Eliminate Air Leaks Flue GAS Sampling Lighting and ShutdownGENERAL-ALL Models Lighting Instructions for STAND- ING Pilot ModelsSequence of Operation for STAND- ING Pilot Standing Pilot ValveGENERAL-DIRECT Ignition Models Furnace if YOU Smell GASOperating instructions for M1M Models with Direct IgnitionOperating Instructions for OIL and GAS GUN Furnace Oil Gun ModelSequence of Operation for OIL GUN Models Oil Furnace Honeywell R7184 ControlSequence of Operation for GAS GUN Models Furnace Controls and FUNC- TionsService Guide Burner AdjustmentsFactory Combustion Air Settings Combustion AIRElectrode Setting Oil Gun Only Oil Gun OnlyGAS Conversion Atmospheric and Direct Ignition FurnacesTroubleshooting Standing Pilot Models Burner AdjustmentsControl Module Status Indicators M1M Series Troubleshooting Direct Ignition Furnaces Including GAS GUN Control Module Is Powered Ignitor Does Not Heat UpTroubleshooting OIL GUN Cad Cell Resistance when Sensing flameMaintenance Optional AccessoriesBy Serviceman Additional OIL Furnace MaintenanceCoil Cavity Damper Non-Platinum Series Only Damper without Coil Cavity Non-Platinum Series OnlyCooling Speed/ Evap Coil Wiring Diagrams M1GH 077, 090 Models 710150 08/00 710151 08/00 Blower WireTable Gas and Oil Furnaces, A/C Ready M1 B, S 066, 086 Models Equivalent Orifice Sizes AT High Altitudes High Altitude
Related manuals
Manual 40 pages 21.44 Kb

M1M, M1S, M1B, M1G specifications

Nordyne, a renowned player in the HVAC industry, has introduced a range of high-efficiency gas furnaces, including the M1S, M1G, M1B, and M1M models. Each of these furnaces is designed to provide efficient heating solutions tailored to the needs of homeowners.

The M1S series is well-known for its reliability and performance. It features a single-stage heating process that delivers consistent warmth to any space. With its multi-speed blower, the M1S ensures quiet and comfortable airflow, adapting seamlessly to varying temperature demands. Its robust construction coupled with an energy-efficient design makes it an ideal choice for those looking for dependable heating without sky-high utility bills.

The M1G model steps it up with a two-stage heating system that offers enhanced comfort and efficiency. By operating at a lower speed during milder conditions, the M1G can effectively reduce energy consumption while still maintaining a cozy environment. It is equipped with a variable-speed blower that not only enhances efficiency but also minimizes noise, making it perfect for residential areas. The M1G is designed with advanced safety features, including an integrated control board that monitors furnace functions to ensure optimal performance.

For those seeking a budget-friendly option without compromising on quality, the M1B model provides a solid performance with its straightforward, reliable single-stage heating. While it may lack some of the advanced features found in higher-end models, the M1B is built for ease of use with straightforward controls and maintenance, making it a great option for families.

The M1M model integrates cutting-edge technology with a focus on maximum efficiency. Featuring a modulating gas valve, this model can adjust its output based on real-time heating requirements. This adaptability ensures that the furnace operates at peak efficiency, significantly lowering energy bills and improving overall comfort. The M1M also boasts advanced diagnostic capabilities that allow for easy troubleshooting, thus reducing maintenance time and costs.

In summary, Nordyne's M1 series furnaces—M1S, M1G, M1B, and M1M—offer a range of options to meet diverse heating needs. With technologies designed for efficiency, reliability, and comfort, Nordyne continues to solidify its reputation as a leader in the HVAC market, providing homeowners with effective heating solutions tailored to their lifestyles and budgets.
Top Page Image Contents