|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Symptom | Likely Cause | What to do |
|
|
|
| |
Hum or Buzz that increases or | Improper A/C ground or faulty | Disconnect or mute channels one |
|
|
|
| |
decreases when the mixer level | equipment connected to mixer | at a time to isolate the problem. |
|
|
|
| |
controls are moved. | input. | Refer to the Owner’s Manual of |
|
|
|
| |
|
|
| the faulty equipment for |
|
|
|
|
|
|
| troubleshooting help. |
|
|
|
|
|
| Faulty cable between source | Substitute a |
|
|
|
|
|
| equipment and mixer. | for the suspected faulty cable. |
|
|
|
|
Hum or Buzz. | Improper A/C grounding, ground | Connect all speakers to a |
|
|
|
| |
|
| loops. | common power circuit. |
|
|
|
|
|
|
| “Telescope” the audio ground by |
|
|
|
|
|
|
| using an XLR/F to XLR/M |
|
|
|
|
|
|
| adapter with Pin 1 disconnected. |
|
|
|
|
|
|
|
|
|
|
| |
|
|
| AC power and lighting cables. |
|
|
|
|
|
| Excessively long unbalanced | Use the balanced outputs (if |
|
|
|
|
|
| cable run. | available) of your mixer or source |
|
|
|
|
|
|
| equipment to drive your EON |
|
|
|
|
|
|
| speakers. |
|
|
|
|
|
|
| Use a “DI” (direct injection) box |
|
|
|
|
|
|
| to convert your unbalanced |
|
|
|
|
|
|
| equipment output to a balanced |
|
|
|
|
|
|
| output. |
|
|
|
|
|
| Improper system gain structure. | Reduce the INPUT 1, LINE 2, |
|
|
|
|
|
|
| and LINE 3 controls and increase |
|
|
|
|
|
|
| the output level of your source |
|
|
|
|
|
|
| devices. |
|
|
|
|
The inputs from INPUT 2 & 3 | MIX/LOOP SWITCH set | Set the MIX/LOOP SWITCH to |
|
|
|
| |
aren’t coming out of the | improperly. | the MIX OUT position |
|
|
|
| |
OUT connector. |
| (depressed). See the CAUTION |
|
|
|
| |
|
|
| in the “Switches” section of this |
|
|
|
|
|
|
| manual. |
|
|
|
|
The speaker connected to the | MIX/LOOP SWITCH set | Disengage the MIX OUT switch. |
|
|
|
| |
OUT connector goes up and | improperly. | See the CAUTION in the |
|
|
|
| |
down in volume when I adjust |
| “Switches” section of this |
|
|
|
| |
the INPUT 1 control on the 1st |
| manual. |
|
|
|
| |
speaker. |
|
|
|
|
|
| |
Speakers feedback and howl | Microphones are pointed into the | Move the speakers so they do not |
|
|
|
| |
when the microphone volume is | speakers. | point into the microphone’s pick- |
|
|
|
| |
turned up. |
| up pattern. See the section on |
|
|
|
| |
|
|
| “Loudspeaker Placement and |
|
|
|
|
|
|
| Mounting” on page 20. |
|
|
|
|
|
| Equalizer settings are incorrect. | Locate the feedback frequency |
|
|
|
|
|
|
| and reduce it using the mixer EQ |
|
|
|
|
|
|
| or an external equalizer. |
|
|
|
|
|
| Excessive gain. | Reduce the gain at the mixer and |
|
|
|
|
|
|
| move the microphone closer to |
| 15 |
| |
|
|
| the sound source. |
|
| ||
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|