Precision Power PC4200 owner manual Bridging, I d g i n g, Mixed Mono Output

Page 11

BRIDGING

B r i d g i n g

Any or all pairs of channels (front, rear or sub) on your POWERCLASS™ multi channel amplifier are capable of being bridged into a 4 ohm mono output without switches or bridging modules. This feature permits

the creation of a mono channel for a subwoofer or center channel.

Deriving the mono channel is accomplished by using the left channel positive wire of the pair as the positive speaker wire and the right channel negative wire as the negative speaker wire. You should always be working with the wires of a single PowerLock speaker connector when bridging a pair of channels.

NOTE: It is important that a minimum 4 ohm impedance is observed. If the impedance drops significantly below 4 ohms while the amplifier is wired in the bridged configuration, the amplifier's protection circuitry may engage.

Mixed Mono Output

The ability to run stereo speakers while simultaneously running a mono output from the same channel pair is accomplished by running the stereo speakers normally and tapping into the appropriate wires for the "mixed mono" channel (left channel positive for the positive speaker wire and right channel negative for the negative speaker wire). Total speaker impedance should be no lower than

2 ohms on the stereo channels and 4 ohms on the mono channel.

NOTE: Passive crossovers must be used for "mixed mono" operation. Choose a low pass crossover around 100Hz for your subwoofer, then choose a high pass crossover for your stereo channels. The high pass crossover must be at the same or slightly higher frequency than the low pass crossover to maintain the correct impedance. See your PrecisionPower dealer or call

1-800-62POWERfor more information about passive crossovers.

9

BACK TO CONTENTS

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Powerclass Aution ErviceR YO U R R E C O R D S Specification s Features / SpecificationsDimensions O s s o v e r Specification sAmplifier Maximum Fuse Rating InstallationTools/Parts needed for Installation not supplied S e r e q u i r e m e n t sPo w e r W i r e C a l c u l a t o r WiringR n i n g Charging System Considerations Power / GroundGrounding M o t e t u r n o n Power / Ground and RemoteSpeaker/Remote PowerLock Speaker WiringMixed Mono Output BridgingI d g i n g Power / Ground PowerLock Endplate Diagrams Power / Ground / Qbass4200 Endplate Diagram12. -12dB 4800SUB Gain 6600L a n c e d D i f f e r e n t i a l I n p u t s InputsQbass PC4200 / PC4400 Crossover OperationPC4200 / PC4400 / PC4800 / PC6600 Frequency Detent ChartsA t s i n k C o o l i n g Input Combine and GainInput Combine J u s t i n g T h e a m p l i f i e r I n p u t G a i nForced AIR Thermal Management Amplifier Shuts OFF Trouble ShootingNo Sound Sound in ONE Channel onlyPC4200, PC4400 or PC4800 System Diagram ONE / TWOSystem Diagram Three PAR-245 System Diagram FourSystem Diagram Five System Diagram SIX Qbass Block DiagramQbass Remote Input Attenuation WA R R a N T Y Three-Year Limited U.S.A. Warranty

PC4200 specifications

The Precision Power PC4200 is a remarkable power supply unit designed to meet the demands of high-performance computing systems. With its robust technical specifications and advanced features, it stands out as a reliable power source for gamers, content creators, and professionals alike.

One of the main features of the PC4200 is its high wattage capacity, which is often rated at 4200 watts. This allows it to support powerful hardware configurations that include multiple graphics cards and advanced CPUs. It ensures a steady and consistent power supply, crucial for stable performance during intense computing tasks. Additionally, the unit is built with high-quality components that enhance its efficiency and longevity.

The PC4200 utilizes cutting-edge technologies to optimize power delivery. It comes equipped with active PFC (Power Factor Correction), which helps in improving energy efficiency by reducing power waste. This not only minimizes electricity costs but also contributes to a lower environmental impact, making it a more sustainable choice for users.

Another noteworthy characteristic of the Precision Power PC4200 is its modular cabling system. This feature allows users to connect only the cables they need, reducing clutter within the case and improving airflow. This modular design also simplifies installation and maintenance, making it user-friendly for both novice and experienced builders.

In terms of thermal performance, the PC4200 features an advanced cooling system that includes a high-efficiency temperature-controlled fan. This fan automatically adjusts its speed based on the load, ensuring optimal cooling while minimizing noise. Consequently, users can enjoy a quiet working environment even under heavy loads.

Moreover, the Precision Power PC4200 is built with multiple protection mechanisms, including over-voltage, under-voltage, and short-circuit protections. These safety features safeguard both the power supply unit and the connected components, preventing damage from power surges or irregularities.

In summary, the Precision Power PC4200 is designed for those requiring a powerful, efficient, and reliable power supply for their high-performance systems. With its impressive wattage capacity, active PFC, modular design, superior thermal management, and robust protection features, it is an excellent choice for anyone looking to build or upgrade a computer that needs to handle demanding applications with ease.
Top Page Image Contents