Graco P20LCM, P39LCS, P40RCM important safety instructions For L20c Air Controls

Page 14

Start Up and Adjust Pump

4.For L20c Air Controls:

a.Close elevator director valve. The ram will slowly drop.

b.If necessary, press blowoff push button to pause elevator descent.

Air Motor Regulator

Blowoff Push Button

 

ElevatorDirector

 

Valve

Air Motor Valve

r_257302_312376_2e

FIG. 10: L20c Air Controls

 

5.Reduce the air motor regulator pressure and open the air motor valve.

6.Adjust air motor regulator until the pump starts.

7.Cycle the pump slowly until all air is pushed out and the pump and hoses are fully primed.

8.Release the gun/valve trigger and lock the trigger safety. The pump should stall against pressure.

To reduce the risk of fluid injection, do not use your hand or fingers to cover the bleed hole on the under- side of the bleed valve body (P) when priming the pump. Use the handle or a crescent wrench to open and close the bleed plug. Keep your hands away from the bleed hole.

9.If the pump fails to prime properly, open the pump bleed valve (P) slightly. Use the bleed hole, on the underside of the valve, as a priming valve until the fluid appears at the hole. Close the plug.

Always use lowest possible fluid pressure to bleed air out of pump.

P

ti10420a

FIG. 11

When changing fluid containers with the hose and gun/valve already primed, open the pump bleed

valve (P), to help prime the pump and vent air before it enters the hose. Close the valve when all air is eliminated.

CAUTION

Do not allow the pump to run dry. It will quickly accel- erate to a high speed, causing damage. If your pump is running too fast, stop it immediately and check the fluid supply. If the container is empty and air has been pumped into the lines, refill the container and prime the pump and the lines, or flush and leave it filled with a compatible solvent. Eliminate all air from the fluid system.

10.With the pump and lines primed, and with adequate air pressure and volume supplied, the pump will start and stop as you open and close the gun/valve. In a circulating system, the pump will speed up or slow down on demand, until the air supply is shut off.

11.Use the air motor regulator (see FIG. 10) to control the pump speed and the fluid pressure. Always use the lowest air pressure necessary to get the desired results. Higher pressures cause premature tip/noz- zle and pump wear.

14

312376L

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Check-MatePump Packages P20LCM Model Shown P39LCS Model Shown P40RCM Model ShownContents Related ManualsModels Skin Injection Hazard Equipment Misuse Hazard Key Component Identification, Supply Unit InstallationCM14BA Model Shown CM7B1G Model Shown Component Identification, Typical Installation Installation GroundingAir Line Accessories System AccessoriesMounting Accessories Fluid Line AccessoriesDisplacement Pump Torque SetupFollow Pressure Relief Procedure on Wet CupPressure Relief Procedure For D200s, D200, D60 and S20 Air Controls See FIGFor D200s, D200, D60, and S20 Air Controls D200s, D200,D60, and S20 SystemsFor L20c Air Controls L20c Air ControlsOvernight Shutdown Follow Pressure Relief Procedure,Shutdown For D200s, D200, D60, and S20 Supply SystemsTroubleshooting Problem Cause SolutionTroubleshooting Required Tools Disconnect Displacement PumpRepair Ti10508a Reconnect Displacement Pump Repair 312376L Parts Pump Package Parts ListReed Switch Assembly NXT200, NXT400, NXT700, NXT1200, and NXT1800 Air MotorsAdapter Bracket 15M222 NXT2200, NXT3400, and NXT6500 Air MotorsModel P40RCM Shown Model P39LCS ShownVarying Parts Pump Packages with L060xx Displacement PumpsCommon Parts P20SCS Pump Packages with L100xx Displacement Pumps Ref. Part Description QtyTie Rod Assy Coupler Lanyard Adapter Pump Packages with L200xx Displacement PumpsCoupling Cover Hairpinw Bracket Rod Assy Coupler Pump Packages with L250xx Displacement PumpsCoupling Tie Rod Coupling Pump Packages with L500xx Displacement PumpsNut Dimensions Pump Packages with NXT 2200, NXT 3400, NXT 6500 Air MotorsPump Package Dimensions Technical Data Displacement Flow Rate gpm lpmCalculate Pump Air Flow/Consumption Performance ChartsCalculate Fluid Outlet Pressure Key Air PressurePsig MPa, bar Cycles/min Fluid Pressure in psig MPa, bar Air Air Flow in Scfm m3/min Bar Cycles/min MPa, bar Performance Charts 312376L Graco Standard Warranty Graco Information

P40RCM, P39LCS, P20LCM specifications

Graco, a renowned brand in the world of fluid handling equipment, has developed a series of versatile and high-performance products tailored for various applications. Among these, the Graco P20LCM, P39LCS, and P40RCM stand out for their innovative features, technologies, and characteristics that enhance productivity and efficiency in professional environments.

The Graco P20LCM is a lightweight and portable paint sprayer designed for small to medium-sized projects. It features Graco’s exclusive ProConnect technology, which allows for quick and easy pump replacement, minimizing downtime. The P20LCM also incorporates a SmartControl system that provides consistent pressure and prevents overspray for a flawless finish. Its flexible suction tube allows for drawing paint directly from a bucket, while its compact design ensures ease of transport, making it ideal for contractors and DIY enthusiasts alike.

In contrast, the Graco P39LCS embodies a robust solution tailored for larger projects. This airless paint sprayer is engineered for high efficiency, capable of handling thicker coatings with ease. It boasts a powerful hydraulic system that maintains pressure, ensuring an even application over large surfaces. The P39LCS integrates the Grip and Guard with LED indicators, enhancing user experience and safety. Additionally, its durable construction and advanced filtration system help in prolonging the lifespan of the equipment, reducing maintenance requirements and downtime.

The Graco P40RCM is an advanced model that offers unrivaled versatility and control, making it a preferred choice for professional contractors. This sprayer features advanced electronic controls that enable users to adjust pressure settings on the fly, offering ultimate control over the application process. The P40RCM is compatible with a wide range of coatings, including paints, stains, and sealants, providing flexibility for diverse job needs. Its AutoPrime technology simplifies the priming process, allowing for faster setup and minimal manual intervention. Furthermore, rugged wheels and a durable frame enhance maneuverability and resilience on job sites.

Together, the P20LCM, P39LCS, and P40RCM encapsulate Graco’s commitment to quality and innovation. With user-friendly features, advanced technologies, and robust designs, these products are engineered to meet the demands of professionals and improve efficiency while delivering superior results in every application.
Top Page Image Contents