Panasonic SH-FX80 Wireless system, Attaching the external digital audio player cradle included

Setup8661En&Cf.fmPage4Tuesday,(continued) April18,20066:18PM

Attaching the external digital audio player cradle (included)

The wireless sound system can be used as a stand-alone audio amplifier when an external device (e.g. MP3 play r) is connected to its MUSIC PORT. To conveniently hold the exter al device, you can attach the included pocket-type or stand-type cradle.

Unplug the AC cord and disconnect the external device before attaching

the cradle.

1Hang the cradle on the back of the wireless sound system.

≥ Ensure the antenna mast is raised.

∫Wireless setup diagram for pairing with the SH-FX60

wireless system

≥Your wireless sound system can be used in tandem with the SH-FX60 wireless system.

≥To avoid possible interference, refer also to page 2 “Avoiding interference”.

e.g.

2Secure the cradle with the screw.

Pocket-type cradle attachment 1

2

1

Stand-type cradle attachment

2

SH-FX60 wireless system (not included)

SB-FX80 wireless sound system (included)

[Note[

Your wireless sound system can also be used in tandem with the SC-HT640W home theater system. For pairing, you can follow the same procedure as shown below for the SH-FX60 wireless system.

Pairing your SB-FX80 wireless sound system with the SH-FX60 wireless system (not included)

Preparation

≥The following steps are to be performed after setting up the SH-FX60 wireless system. For proper setup, refer to its operating instructions.

≥Do not remove the SH-FX60T transceiver card from the home theater unit.

≥Store your SH-FX80T transceiver card in a cool dry place for later use.

1	Unplug the SH-FX60 wireless system from the AC outlet.
2	Move the SB-FX80 wireless sound system next to your home
	theater unit.
	≥ After pairing is completed, you can move the SB-FX80 wireless sound system to
	the desired location.
3	Select “MAIN SET” on the SB-FX80 wireless sound system (➜ page 3).
	≥ Ensure the SB-FX80 wireless sound system is plugged into the AC outlet.
4	Reduce the volume on your home theater unit.
5	[For[HT[models] (e.g. SC-HT740)
	Press and hold [SURROUND MUSIC] on your home theater unit

until “P” lights in the display.

≥ Ensure the “REAR MUSIC P.” source is not selected.

[For[RT[models] (e.g. SC-RT50)

1Press [AUX] on your remote control to select “AUX”.

2Press and hold [∫] (Stop) on your home theater unit.

≥Do not release the button.

3Wait at least 5 seconds, and then press [MUTING] on your remote control.

“P” lights in the display.

4Release [∫] (Stop).

6	While “P” is displayed
	Using a pointed object, press [I/D SET] on the back of the SB-FX80
	wireless sound system.
	≥ During pairing, the lighting ring will temporarily light up for a short period of time.
	Back of the SB-FX80 wireless sound system
	Lo	Hi	I/D SET
	SOUND
	AC IN ~
7	Plug the SH-FX60 wireless system back into the AC outlet.
	≥ After the SH-FX60 wireless system and SB-FX80 wireless sound system lighting
	rings both light up, pairing is completed.
	≥ When paired, the SB-FX80 wireless sound system is linked to your home theater
	system only when the SH-FX60 wireless system is also linked.
8	Start play on your home theater unit.

∫To cancel pairing, or to use the SB-FX80 wireless sound system without the SH-FX60 wireless system

1Turn off your home theater unit.

2Swap the SH-FX60T transceiver card with the SH-FX80T transceiver card.

3Turn on your home theater unit.

4Follow steps 2 through 6 (➜ above).

≥Pairing is canceled when the lighting ring lights up. The SB-FX80 wireless sound system can now be used without the SH-FX60 wireless system.

4