Venturer PVS6370 Play Modes for CD or Jpeg Disc, Repeat Playback, Troubleshooting Guide

1/1 ” is

PLAYING A DISC

LOCATING A DESIRED SECTION

VIEWING JPG FILES

CUSTOMIZING THE FUNCTION SETTINGS

This owner’s manual explains the basic instructions for operating this unit. Some DVDs are produced in a manner that allows specific or limited operation during playback. Therefore, this unit may not respond to all operating commands. THIS IS NOT A DEFECT. Please refer to the instructions accompanying the specific DVD in question for more information about the options available on that DVD.

“ ” may appear on the screen during operation. A “ ” means that the desired operation is not permitted by the unit or disc.

Locating a Specific Title

If a DVD contains title numbers, you can locate a specific title by directly selecting its title number.

1.	Press the GOTO button.
2.	Press the corresponding number button(s)
	for the title you want.

permited by the DVD, after you press the ENTER button, it will restore to - - -. You should re-enter correct numbers.

•	Some discs may not respond to this
	process.
•	This method of locating a chapter is
	available only on a DVD that contains
	chapter numbers.

This unit can play JPG files recorded on a CD-R or CD-ROM disc (CD-RW is not recommendable).

Viewing JPG Files

1. Open the disc door.

2. Hold a JPG file disc by its edge and gently push it onto the spindle with the label side facing up until you hear a “click”.

3. Close the disc door. A list of folders/files will appear on the screen.

Language

OSD Language

1. Press the SETUP button in stop mode.

2. Press the button to select OSD Language.

3. Press the ENTER button, then the / button to shift and change the Language.

4. Press the ENTER button.

Playing a Disc

1.Slide the (CHARGE) / STANDBY / ON switch to the ON position.

See CUSTOMIZING THE FUNCTION SETTINGS before proceeding to step 2.

2.Press the OPEN

button and hold the front panel to open the disc door.

3. Hold the disc by its sides and gently push

it onto the spindle with

label side facing towards you until you hear

a “click”.

4.Gently push the disc door closed. It takes a short while for your unit to load the disc. After loading, for most DVDs, the unit will automatically take you main menu or start playing. If the unit does not automatically start playing the DVD, press the PLAY button.

Pausing Playback (Still Mode)

Press the PAUSE button. To resume normal playback, press the PLAY button.

Each time you press the PAUSE button, the picture advances one frame.

2.Press the SUBTITLE button repeatedly to select the desired subtitle language.You can

turn subtitles off by pressing the SUBTITLE button repeatedly until the “ Off ” is displayed.

Notes:

•Some DVDs are set to display subtitles automatically, and you cannot turn them off even if you set the subtitle function to off.

•During some scenes, the subtitles may not appear immediately after you select your desired scene.

•The number of subtitle languages recorded differs depending on the disc. If only one language is recorded, the language does not change.

•This function can only be used for discs on which subtitles have been recorded in multiple languages.

•Some DVDs allow you to change subtitles only via the disc menu. If this is the case, press the MENU button and choose the appropriate subtitle on the disc menu.

Angle Selection

Some DVDs contain scenes which have

3. Press the ENTER button to confirm.

Playback starts from the selected section.

Notes:

•If the title numbers you entered is not permited by the DVD, after you press the ENTER button, it will restore to - - -. You should re-enter correct numbers.

•Some discs may not respond to this process.

•This method of locating a title is available only on a DVD that contains title numbers.

Locating a Specific Chapter

If you know the chapter number for the chapter that you want to play, you can locate it by directly selecting that number.

1. Press the GOTO button.

2. Press or button to display Chapter and press the corresponding number button(s) for the chapter you want.

3.Press the ENTER button to confirm. Playback starts from the selected section.

Notes:

• If the chapter numbers you entered is not

Locating a Specific Time

You can move to a specific location by entering its corresponding time (hours, minutes, seconds).

1.Press the GOTO button.

2.Press or button to display Time and press the corresponding number buttons for the setting point you want.

3.Press the ENTER button to confirm. Playback starts from the selected section.

Notes:

•If the time numbers you entered is not permited by the DVD, after you press the ENTER button, it will restore to - - : - - : - . You should re-enter correct numbers.

•Some discs may not respond to this process.

•Some scenes may not be located as precisely as you specified.

•This method for accessing specific locations is available only within the current title of the DVD.

4. Press the or button to select your desired file, the selected picture will appear at the lower right corner. Press the PLAY button to start playback. Press the button to display a folder list.

Notes:

•You can press the PAUSE button to interrupt playback. Press the PLAY button to resume playback.

•You can press the STOP button to quit playback.

•You can press the PREV or NEXT button to change the picture.

•You can press the ANGLE button to rotate direction of the picture by 90o.

•Some discs may not permit this operation.

PLAY MODES FOR CD OR JPEG DISC

Play Modes for CD or JPG Disc

When play CD / JPG discs, you can modify the Play Modes through the Toolkit which appears on

the right of below picture on the screen. Press the				/ button to navigate between the windows
and the		/	button to select files/tracks or play mode items.
Then press the ENTER button.
1.	In Stop mode, press the Cursor buttons ( , ,			, ) to select
	"Edit mode" then press the ENTER button.
2.	Use the Cursor buttons ( , , , ) to select tracks/files shown
	on the left hand side of the window. Press the ENTER button
	to confirm the selected tracks/files. " " will appear in front of
	the selected tracks/files.

3. Select "Add to program", then press the ENTER button. " "

will disappear from the screen. It means that the tracks/files you have selected are added into

5. Press the SETUP or RETURN button to exit the menu.

Subtitle

1. Press the SETUP button in stop mode.

2. Press the button, then the / button to select Subtitle.

3. Press the ENTER button, then the / button to shift and change the Language.

4. Press the ENTER button.

5. Press the SETUP or RETURN button to exit the menu. Notes:

•Some DVDs may be set to display subtitles in a language other than the one you selected. A prior subtitle language may be programmed on the disc.

•Some DVDs allow you to change subtitle selections only via the disc menu. If this is the case, press the MENU button and choose the appropriate subtitle language from the selection on the disc menu.

Audio

1.	Press the SETUP button in stop mode.
2.	Press the button, then the / button to select Audio.
3.	Press the ENTER button, then the / button until your
	preferred Audio is displayed.
4.	Press the ENTER button.
5.	Press the SETUP or RETURN button to exit the menu.

Note: Some DVDs may not play in the language you selected. A prior language may be programmed on the disc.

DVD Menu

1. Press the SETUP button in stop mode.

Stopping Playback

Press the STOP button at the location where you want to interrupt playback. To resume

been shot from a number of different angles. For these discs, the same scene can be viewed from each of these different angles.

REPEAT PLAYBACK

You can play a specific title or chapter repeatedly. (Title repeat, chapter repeat, A-B repeat)

the "Program view".

4. Select "Program view" to view programmed files. To add more files by "Browser view" follow

above steps.

2.	Press the button, then the / button to select DVD Menu.
3.	Press the ENTER button, then the / button until your
	preferred DVD Menu language is displayed.

playback at the position where the disc was stopped, press the PLAY button.

If you press the STOP button twice, the unit’s memory will be cleared and pressing the PLAY button will reset the disc to the beginning.

Fast Forward / Fast Reverse

1.Press the SEARCH or SEARCH button when a disc is playing. Each time you

press the SEARCH or SEARCH button, the playback speed changes in the following sequence:

2.Press the PLAY button when you reach the desired point to resume normal playback.

Notes:

•The DVD player mutes sound and subtitles during reverse and forward scan of DVDs.

•The fast playback speed may differ depending on the disc.

Skip (Forward / Reverse)

•Press the PREV button to go back to current or previous chapters/tracks.

•Press the NEXT button to advance chapters/tracks.

•For audio CDs, use the number buttons on the remote control to jump immediately to the desired track number.

1.While you are playing a DVD with different angles recorded, press the ANGLE button to view the number of current angles available.

2.Press the ANGLE button repeatedly to

change the scene to the next recorded angle.

•After approximately two seconds, playback will continue from the new angle you selected.

•If no button is pressed within 10 seconds,

playback continues without changing the current angle.

Notes:

•This function can only be used for discs on which scenes shot from multiple angles have been recorded.

• If only one angle is recorded, “

Sequence of angle shots

(Example)

displayed.

Display Function

While the disc is playing, press the DISPLAY button repeatedly to display information on operation status.

Repeating a Chapter

1.While the DVD is playing, press the REPEAT DISC button until the Repeat Chapter ” indicator displays on the screen. The current chapter is played

repeatedly.

Repeating a Title

2.While the DVD is playing, press the REPEAT DISC button until the Repeat Title ” indicator displays on the screen.The current title is played repeatedly.

To Resume Normal Playback

3.While the DVD is playing, press the REPEAT DISC button until the

Repeat Off ” indicator displays on the screen.

You can play a single track or the whole disc repeatedly.

Repeating a Single Track

1.While the CD disc is playing, press the REPEAT DISC button until the “ Repeat single ” indicator displays on the screen. The current track is played repeatedly.

Repeating a Whole Disc

2.While the CD disc is playing, press the REPEAT DISC button until the “Repeat all ” indicator displays on the screen.The whole disc is played repeatedly.

To Resume Normal Playback

3. Press the REPEAT DISC button until the “ Repeat off ” indicator displays on the screen.

Repeating a Specific Section

You can play a specific section repeatedly.

1.While the disc is playing, press the REPEAT A-Bbutton at the beginning of the section (“Rep A- ” is displayed) you want to play repeatedly.

2.Press the REPEAT A-Bbutton again at the end of the section (“ Rep A-B ” is displayed).

3.The Unit will immediately begin replaying your selection.

To Resume Normal Playback

4.While the disc is playing, press the REPEAT A-Bbutton until the “ RepA-B Off ” indicator displays on the screen.

Note:

•Some discs may not permit A-B repeat operation.

•You cannot set the A-B repeat function for a segment that includes multiple camera angles.

•You can specify a segment only within the current title or track.

•There may be a slight difference between point A and the location where playback actually resumes depending on the disc.

5. Press the PLAY button to start the program playback.

The Toolkit has the following play mode items:

•Repeat ( Off / Single / All ): Off: Resumes normal playback. Single: Repeats the current track/file.

All: Repeats all files on the current folder or all tracks on the disc.

•Mode ( Normal / Shuffle / Music intro ): Normal: Resumes normal playback. Shuffle: Playbacks track/file in random order.

Music intro (for Audio CD only): Only playbacks the first 10 seconds of all the tracks on the current folder/disc.

•Edit mode: Program operation works only when "Edit mode" is selected.

•Program view: To view tracks/files in the "Program view" list. It is disabled when the "Program view" list is empty.

•Add to program: Add files/tracks to the "Program view" list. It is disabled if the "Edit mode" is not selected.

•Browser view: To view files/tracks in the original view list.

•Clear program: Delete the files/tracks in the "Program view" list.

Select a file/track or more you want to delete in complete stop mode (press the STOP button twice). " " will appear beside the deleted file/track. Select "Clear program" and then press the ENTER button. It is disabled if the "Edit mode" is not selected.

Note: The program will be deleted if the STOP button is pressed twice, the disc door is opened, or selected files are deleted by selecting "Clear program".

TROUBLESHOOTING GUIDE

SYMPTOM	CAUSE (AND REMEDY)
No power.	•	Ensure the car power adapter is connected.
	•	Make sure that the unit is turned on.

4.	Press the ENTER button.
5.	Press the SETUP or RETURN button to exit the menu.

Note: Some DVDs may not include your pre-selected language. In this case, the DVD player automatically displays disc menus consistent with the disc's initial language setting.

Video

Aspect Ratio

1.	Press the SETUP button in stop mode.
2.	Press the	/ button to select Video.
3.	Press the	button, then the / button to select Aspect Ratio.
4.	Press the ENTER button, then the		/	button to shift and
	change the aspect ratio.

5.Press the ENTER button.

6.Press the SETUP or RETURN button to exit the menu. Notes:

• The displayable picture size is preset on the DVD. Therefore, the playback picture of some DVDs may not conform to the picture size you select.

• When you play DVDs recorded in the 4:3 picture size only, the playback picture always appears in the 4:3 picture size regardless of the Aspect Ratio setting.

• Select 16:9 to conform the LCD screen on the unit. Always be sure that your Aspect Ratio conforms to the actual TV in use if you connect the unit to a TV.

View Mode

1.	Press the SETUP button in stop mode.
2.	Press the	/ button to select Video.
3.	Press the	button, then the / button to select View Mode.
4.	Press the ENTER button, then the		/	button to shift and
	change the View Mode.

5.Press the ENTER button.

6.Press the SETUP or RETURN button to exit the menu.

Fill Fill the screen with decoded image.

Audio Selection

DVD PROGRAMMABLE MEMORY

Very little or no sound • Make sure that you select ON mode.

Original	Display image as it’s original size.
Auto Fit	Automatically fit the decoded image on screen without distortion. Black bars will be

On some DVDs, the sound is recorded in two or more formats. Follow the directions below to select the preferred

language and sound system.

1.While a disc is playing, press the AUDIO button to show the current audio format number.

2.Press the AUDIO button repeatedly to select

the desired audio format. Notes:

•If only one audio format is recorded on the DVD, the number does not change.

•Some DVDs allow you to change audio selections only via the disc menu. If this is the case, press the MENU button and choose the appropriate language on the disc menu.

•You can select different audio channels (Stereo, Left or Right) on an Audio CD by pressing the AUDIO button repeatedly.

Subtitle Selection

1. While a DVD is playing, press the SUBTITLE button to display the current

language setting, as shown in the example.

Elapsed Time:

Elapsed time from the beginning of the title which is currently playing.

Remain Time:

Remaining time of the title which is currently playing.

Adjust the LCD Screen

You can adjust brightness, contrast, color or view mode of the LCD screen.

1.	Press the TV MODE button.
2.	Press the /	button to select Brightness,
	Contrast, Color or View Mode.
3.	Then press the	/ button to change the
	setting. (For View Mode, press the ENTER
	button to change the setting.)
4.	Press the TV MODE button to exit the menu.

Playing TItles/Chapters in a Favourite Order

You can combine your favourite titles/chapters and play them in the order you determine.

1.When a DVD is stopped, press the MEMORY button, the following display appears.

2.	Select the items in the order you want by pressing the
	number buttons.
	Each time you press the Cursor buttons ( , , , ),
	the space is highlighted. Highlight where you want to enter,
	then press the corresponding number buttons.
3.	Press the Cursor buttons ( , , , ) to move the highlighted bar to Play Memory, then
	press the ENTER button. The DVD player starts memory playback.

4.To resume normal playback from memory playback

a)Press the MEMORY button in stop mode.

b) Press the Cursor buttons (, , , ) to move the highlighted bar to “Clear All”, then press the ENTER button. All the input programs will be cleared.

c)Press the PLAY button to resume normal playback. Notes:

•If the title or chapter numbers you entered is not permited by the DVD, after you press the ENTER button, it will restore to - - -. You should re-enter correct numbers.

•Some discs may not permit memory playback operation.

•If you select repeat during memory playback, the DVD player repeats the current memory playback.

•If you press the MEMORY button while the display appears on the TV screen, the display disappears.

•The programmed selections will be cleared when you open the disc tray or turn off the DVD player.

is coming from a DVD.	•	Make sure the unit is not paused. Press the		PLAY button.
	• Make sure the unit is not in fast-forward or fast-reverse mode. Press
		the	PLAY button.
	• Make sure the AUDIO/VIDEO input/output connections are correct.
	• The DTS DVD cannot be decoded to have speaker output.
	• The unit has overheated. Shut it off for 30 minutes to allow it to cool
		down.
No picture.	•	The region number of the disc doesn't match the region number of
		this unit.
The picture is not clear.	•	The DVD is dirty. Gently clean the disc.
	• The disc is scratched.
	• Please adjust the LCD's brightness, contrast and color using theTV
		MODE button on the remote control.
Loud hum or noise is	•	The plugs and jacks are dirty.Wipe them with a cloth slightly moistened
heard.		with alcohol.
	•	Clean the disc.
The disc does not play.	•	There is no disc inside the unit ("No Disc" appears on the screen).
	• Insert the disc correctly with the graphics facing up.
	•	Clean the disc.
	• A non-NTSC disc has been inserted, or the disc region number does

not match the region number of the unit.

• Condensation may have formed inside the unit due to a sudden change in temperature.Wait about an hour for it to clear and try again.

Specifications and external appearance are subject to change without notice.

present on top/bottom or left/right of screen.

Pan Scan Select when a standard 4:3 TV is connected. Displays pictures cropped to fill your

		TV screen. Sides of the picture are cut off.
Note: Depending on the DVDs, you may not be able to view the mode as selected.
Misc
Use Default Settings
1.	Press the SETUP button in stop mode.
2.	Press the	/ button to select Misc.
3.	Press the	button, then press the	/	button to select “Use
	Default Settings” dialogue box.
4.	Press the ENTER button then press the			/	button to select
	“Yes”. Press theENTER button. The original setting will be
	restored. The unit will exit setting menu automatically and re-
	load the disc in the disc tray.
Note: It will take 3-5 seconds to reset the DVD player to the factory default.
Screen Saver
1.	Press the SETUP button in stop mode.
2.	Press the	/ button to select Misc.
3.	Press the	button, then press the	/	button to select Screen
	Saver.
4.	Press the ENTER button, then press the			/	button to change
	the On/Off mode.
5.	Press the ENTER button.
6.	Press the SETUP or RETURN button to exit the menu.					811-637091W010
						Printed in China