JVC XL-PM25SL Using the Remote Control, Using with an audio system, How to use the remote control

Page 6

Anti-Shock Protection Preventing Accidental Operation (Hold mode)

This function minimizes sound interruption caused by vibrations,

 

 

 

by utilizing audio data that has been stored in the memory ahead

 

 

 

of the following time:

ON

HOLD

OFF

For Audio CD: Up to 45 seconds worth (Anti-Shock Protection

 

on/off selectable)

For MP3:

Up to 120 seconds worth at 128 kbps (Anti-Shock

 

Protection is fixed to on.)

Normally, “ASP” and the A.S.P. progress meters are displayed

and the Anti-Shock Protection is in effect.

 

 

 

A.S.P. indicator

When the disc is played, as the audio data gradually stored in the memory, the A.S.P. progress meter progresses.

[Fully stored]

HOLD

To cancel (Audio CD only)

Press the A.S.P./T.SEARCH button in stop mode or during playback. “ASP OFF” appears on the display.

To activate again (Audio CD only)

Press the A.S.P./T.SEARCH button.

Notes:

The Anti-Shock Protection can be enabled or disabled during play, and this may cause a slight interruption in the sound be- cause the disc’s rotational speed changes.

Turning off the Anti-Shock Protection will save battery life more or less.

The HOLD switch on the unit/remote control is prepared to pre- vent an accidental operation by an unexpected button press.

Hold mode prevents the following:

Powering on the unit accidentally (which can cause the batter- ies to go dead).

Play being cut off unexpectedly.

Unexpected operation during play. (Set the HOLD switch to the ON position after you start playing disc.)

To set the unit/remote control in Hold mode

Set the HOLD switch on the unit/remote control to the ON po- sition. The all buttons on the unit/remote control are disabled.

“HOLD” indication

When the unit is in Hold mode, “HOLD” will be displayed if a button on the unit is pressed.

To release the Hold mode

Set the HOLD switch to OFF position.

Notes:

Before turning on the unit, be sure that HOLD is OFF. Otherwise, you cannot turn on the unit.

The HOLD switch on the unit is effective for the unit only. While, that on the remote control is effective for the remote control only.

Using the Remote Control

Preparation:

Release the remote control from the Hold mode.

HOLD

How to use the remote control

Press during off or stop mode.

To start play

Press during play.

To stop play

Press during stop mode.

To turn off the unit

Skip function

Press during play.

Forward

Fast forward/reverse

Reverse

Search function

Keep depressed during play.

When adjusting the volume using the remote control, set the volume control on the unit to an appropriate position.

To adjust the volume

Using with an audio system

You can use an audio system by connecting it to the unit with a stereo connection cable (not sup- plied).

Connect the cable to the amplifier after turning off its power.

Do not connect the cable to the PHONO jacks on the amplifier.

Obtain the optional connecting cable if the amplifier comes with mini-phone jacks.

Adjust the volume level on the amplifier.

LINE OUT jack

Left side panel of the unit

Stereo connection cable

(not supplied)

Amplifier

 

(White)

 

(Red)

 

Note:

To obtain original sound, turn HBS to OFF. Also, set the sound effect to “FLAT”. (See page 7)

6

Image 6
Contents How to hold a disc If the disc surface is dirty PrecautionsHow to remove a disc from its case Check the packing carton for these accessoriesSpecifications Unit Symptom Check this Maintenance TroubleshootingPortable CD player a Remote control B DisplayHow to use the AC plug adaptor not sup- plied Power Supply PreparationsRecharging procedure About MP3 filesBasic Play Follow the steps in the numerical orderMP3 Using the Remote Control Using with an audio systemHow to use the remote control Other Play Methods Select the desired track. e.gResume Group search Stop mode or during playbackTitle search MP3 only File search Alphabet search Enter the characters CH, for example