JVC HR-DVS2U manual Start Dubbing, END Audio Dubbing

Page 59

LAY

STOP	PAUSE

T

W

1 2 3

2

4 5 6

7 8 9

04

1

DV

S-VHS

PLAY

PAUSE

STOP

3

EN59

START DUBBING

6 Engage the audio component's Play mode, then press PLAY to start the tape in your VCR. Audio dubbing begins at this point.

●When monitoring the audio-dubbed sound on the DV deck, set "12BIT MODE" to "SOUND2". ( pg. 33)

● blinks and is displayed on the front display panel.

●To stop dubbing temporarily, press PAUSE. Press PLAY to resume dubbing.

END AUDIO DUBBING

7 Press STOP to stop the tape in your VCR, and engage the audio component's Stop mode.

NOTES:

●Once the Audio Dubbing starts, you can not use the other deck.

●When monitoring the sound during Audio Dubbing, the normal soundtrack is automatically selected. If you wish to hear the Hi-Fi or mixed sound (Hi-Fi + Normal soundtracks), refer to the "Select The Soundtrack" section ( pg. 32) and select the soundtrack you wish to hear. (VHS deck only)

●Audio dubbing stops automatically when the counter reaches "0:00:00", and the VCR enters the Play mode. Check the counter reading before dubbing. (VHS deck only)

●Audio dubbing is also possible using the rear AUDIO IN connectors.

●Audio dubbing cannot be performed on a VHS/S-VHS cassette that has had its record safety tab removed, or on a Mini DV cassette that has had its erase protection switch set to "SAVE".

●When playing back an audio-dubbed tape on the VHS deck, refer to the "Select The Soundtrack" section ( pg. 32) to select the soundtrack you wish to hear. When playing back an audio-dubbed Mini DV tape on the DV deck, set "12BIT MODE" to "SOUND2" ( pg. 33).

●Picture may be distorted during Audio Dubbing Pause.

●It may be unlawful to record or play back copyrighted material without the consent of the copyright owner.

●Audio dubbing is not possible using the DV IN/OUT connector.

Image 59

Contents HR-DVS2U Do not place the VCR Dear CustomerAntenna Installation Instructions InstallationServicing Before YOU Install Your NEW VCRUSE Contents Connections RF Cable supplied Connect VCR to TVBack of VCR Audio/Video Cable suppliedAuto Clock Set/Auto Tuner Set Plug & Play SetupPlug & Play EN Initial Sett IngsLanguage EN Initial Settings Access Main Menu ScreenAccess Initial SET Screen Access Clock SET ScreenSemi-Auto SET Auto Clock to onSelect Host Channel SET Time Select D.S.T. ModeSelect Time Zone Return to Normal ScreenSet Receivable Channels Access Tuner SET ScreenTuner SETScreen Access Main Menu ScreenAccess Manual Channel SET Add Or Delete a ChannelConnect Cable BOX to VCR Cable Box ControlSituate Controller Attach ControllerSet Cable Box Output Channel & Cable Box Brand Access Cable BOX SET ScreenTurn on Cable BOX Select Cable BOX Output ChannelBrand Code Access Cable BOX Brand SET ScreenEnter Cable BOX Brand DBS receiver DBS Receiver ControlConnect DBS Receiver to VCR On Next Turn on DBS ReceiverSelect DBS Receiver Set DBS Receiver Output Channel & DBS Receiver BrandJVC Access DBS ReceiverDBS Receiver Code from Following list, then Press OK JVC Dish Network Echostar Dish NetworkSimple Playback 22 EN Simple RecordingDV Deck Select DV Deck24 EN Playback FeaturesSlow Motion/Reverse Slow Activate HIGH-SPEED SearchVariable-Speed Search/ Reverse Motion Playback Still Picture/Frame-By-Frame26 EN Select Superimpose SET Access Mode SET ScreenMode SuperimposeStop Repeat 28 ENStart Repeat Picture Control VHS deck only Video Stabilizer 30 ENDigital R3 VHS deck only Access VHS Mode SET ScreenSelect Digital TBC/NR SET Mode Digital TBC/NR VHS deck onlyOn the Screen On the remote control32 EN Select The SoundtrackSound Mode Selection Access DV Mode SETAccess DV Mode SET Screen Select 12BIT ModeVideo Calibration Active Video Calibration34 EN VHS deck onlyRecording 36 EN Recording FeaturesLocate Start Point Access Mode SETSelect 2ND Audio Record SET Mode Engage RECORD-PAUSE ModeVHS Super VHS, S-VHS Access VHS Mode SETSelect S-VHS Mode 38 ENSuper VHS ET VHS deck only Engage S-VHS ET ModeEnter Pluscode Number VCR Plus+ Timer ProgrammingEN Timer Recording Press PROG. on the remote controlCheck Program Data Engage Timer ModeInput Receiving Channel Number Initial SET, then press Changing VCR Plus+ SettingVCR Plus+ Guide Channel Matching Number Access Guide Channel SET ScreenInput Guide Channel SET Channel Number Express TimerSET Program Stop Time SET Program DatePower Program Access Program Check ScreenAccess Program Screen Check, Cancel And Revise ProgramsSelect Programme to Cancel or Change Programme SettingConfirm Overlapping ProgrammesAuto Timer Timer SET ModeTimer Recording Auto SP→EP TimerDuration Instant TimerEngage ITR Mode SET RecordingDirection Tape DubbingLoad Cassettes Select DubbingEND Dubbing NormalDubbing Pause DubbingPause Random Assemble EditingProgram Editing Memory 8 programmes x 8 scenes Start Editing RECORD-PAUSE ModePrepare Source Tape Engage VHS Deck toLoad a Cassette 54 ENMake Connections Mode SET RECORDER’S Input ModeControl SET Mode Select Front AUX Input SETEditing Edit To Or From Another56 EN Make ConnectionsStart Player SET RECORDER’S Input ModeOUTPUT1 Setting Select Edit for PICVHS Audio Dubbing SET Input ModeAudio Dubbing 58 ENEND Audio Dubbing VHS Insert Editing DV Insert Editing SP Mode OnlyInsert Editing END Insert Editing Reset the CounterEngage Insert Editing Start EditingConnecting To a Video Titler Digital printer Connecting To a PrinterSET TV Brand Code SET Remote Control Mode64 EN Turn on the TVCable BOX Brand Name Brand Code Cable Box Multi-Brand Remote ControlTurn on the Cable BOX Operate Cable BOXTurn on the DBS SET Remote ControlDBS Receiver Multi-Brand Remote Control 66 ENCord Unplug Vcrs PowerPlug in Power Cord Turn VCR Power onThen insert the cassette Clear or USE Cleaning Dealer68 EN Cassette gets stuck partwayThat ‰appears on the front display Panel Re-perform the set-up proceduresTimer again Point is not dubbedRoubleshooting Re-perform the VCR Plus+ setupProcedure pg 70 ENWhat happens if the tape runs out during recording? Questions and Answers ENCan the VCR indefinitely remain in the still mode? Can the VCR indefinitely remain in the Record-Pause mode?Wertyu QDV Record Indicator pg wDisplay Panel pg32Tape Speed Indicators pg 3S Video Input Connector pg4S Video Output Connectors pg Index Point the remote control toward the sensor windowList Of Terms Express Timer ProgrammingPlug & Play Random Assemble Editing Record Safety Tab Video Connection Tape Dubbing Tape Position Indicator76 EN For Servicing Only in U.S.A HOW to Locate Your JVC Service Center78 EN Warranty Only in U.S.AMemo HR-DVS2U