JVC HR-DVS2U manual 64 EN, Turn on the TV, SET Remote Control Mode, SET TV Brand Code, Operate TV

Page 64

64EN

SPECIALFEATURES

AUDIO	MONITOR

POWER

VCR/TV/CABLE/DBS

TV/VCR

	T	W	3
NUMBER	1	2	3		ENTER
NUMBER				2	ENTER
	4	5	6
	7	8	9
		0		4
1		DV	S-VHS
STOP			TV CH +
			TV CH +
TV VOL –					TV VOL +
					TV VOL +
TV CH –		3
		3

TV Multi-Brand Remote Control

The VCR's remote control can control several functions on JVC remote control TVs and on the brands of remote control TVs listed below.

TURN ON THE TV

1 Turn the power on using the TV's remote control.

SET REMOTE CONTROL MODE

2 Set the VCR/TV/CABLE/DBS switch on the VCR's remote control to TV.

SET TV BRAND CODE

3 Refer to the chart below. While holding down POWER on the VCR's remote control, enter your TV’s brand code using the NUMBER keys, then press STOP. Follow the example shown at bottom left.

●Once you have set the remote control to operate the TV, you don’t have to repeat this step until you replace your remote control’s batteries.

●PANASONIC has two codes. If the TV does not function with one code, try entering the other.

OPERATE TV

4 First, press POWER on the remote to see if the TV’s power goes off as it should. If it does, try other operations.

●The POWER, TV/VCR, TV CH +/–,TV VOL +/–,AUDIO MONITOR (TV Muting) and NUMBER keys on the remote can all be used to operate the TV. *For some brands of TV, you must press ENTER after having pressed the NUMBER keys.

●To return the remote to VCR control, set the VCR/TV/ CABLE/DBS switch to VCR.

TV BRAND NAME	BRAND CODE
JVC	01
MAGNAVOX	02
MITSUBISHI	03
PANASONIC	04, 11
RCA	05
SHARP	06
SONY	07
TOSHIBA	08
ZENITH	09
HITACHI	10
SAMSUNG	12
SANYO	13
SEARS	13

NOTE:

Depending on the type of TV, there may be cases where some or all functions cannot be operated using the remote control.

(Ex.) To set remote control to RCA 05:

POWER
0	5	STOP	Release

Hold down	Press in succession

Image 64

Contents HR-DVS2U Dear Customer Do not place the VCRInstallation Antenna Installation InstructionsUSE Before YOU Install Your NEW VCRServicing Contents Connections Connect VCR to TV Back of VCRAudio/Video Cable supplied RF Cable suppliedPlug & Play Setup Plug & PlayEN Initial Sett Ings Auto Clock Set/Auto Tuner SetLanguage Access Main Menu Screen Access Initial SET ScreenAccess Clock SET Screen EN Initial SettingsSelect Host Channel SET Auto Clock to onSemi-Auto Select D.S.T. Mode Select Time ZoneReturn to Normal Screen SET TimeAccess Tuner SET Screen TunerSET Set Receivable ChannelsAccess Main Menu Screen Access Manual Channel SETAdd Or Delete a Channel ScreenCable Box Control Situate ControllerAttach Controller Connect Cable BOX to VCRAccess Cable BOX SET Screen Turn on Cable BOXSelect Cable BOX Output Channel Set Cable Box Output Channel & Cable Box BrandEnter Cable BOX Brand Access Cable BOX Brand SET ScreenBrand Code Connect DBS Receiver to VCR DBS Receiver ControlDBS receiver Turn on DBS Receiver Select DBS ReceiverSet DBS Receiver Output Channel & DBS Receiver Brand On NextAccess DBS Receiver DBS Receiver Code from Following list, then Press OKJVC Dish Network Echostar Dish Network JVCSimple Playback Simple Recording 22 ENSelect DV Deck DV DeckPlayback Features 24 ENActivate HIGH-SPEED Search Variable-Speed Search/ Reverse Motion PlaybackStill Picture/Frame-By-Frame Slow Motion/Reverse Slow26 EN Access Mode SET Screen ModeSuperimpose Select Superimpose SETStart Repeat 28 ENStop Repeat Picture Control VHS deck only 30 EN Video StabilizerAccess VHS Mode SET Screen Select Digital TBC/NR SET ModeDigital TBC/NR VHS deck only Digital R3 VHS deck onlyOn the remote control 32 ENSelect The Soundtrack On the ScreenAccess DV Mode SET Access DV Mode SET ScreenSelect 12BIT Mode Sound Mode SelectionActive Video Calibration 34 ENVHS deck only Video CalibrationRecording Recording Features 36 ENAccess Mode SET Select 2ND Audio Record SET ModeEngage RECORD-PAUSE Mode Locate Start PointAccess VHS Mode SET Select S-VHS Mode38 EN VHS Super VHS, S-VHSEngage S-VHS ET Mode Super VHS ET VHS deck onlyVCR Plus+ Timer Programming EN Timer RecordingPress PROG. on the remote control Enter Pluscode NumberInput Receiving Channel Number Engage Timer ModeCheck Program Data VCR Plus+ Guide Channel Matching Changing VCR Plus+ SettingInitial SET, then press Input Guide Channel Access Guide Channel SET ScreenNumber Express Timer SET Program Stop TimeSET Program Date SET Channel NumberPower Access Program Check Screen Access Program ScreenCheck, Cancel And Revise Programs ProgramCancel or Change Programme Setting Confirm OverlappingProgrammes Select Programme toTimer SET Mode Timer RecordingAuto SP→EP Timer Auto TimerInstant Timer Engage ITR ModeSET Recording DurationTape Dubbing Load CassettesSelect Dubbing DirectionNormal DubbingPause Dubbing END DubbingProgram Editing Memory 8 programmes x 8 scenes Random Assemble EditingPause RECORD-PAUSE Mode Prepare Source TapeEngage VHS Deck to Start EditingMake Connections 54 ENLoad a Cassette SET RECORDER’S Input Mode Control SET ModeSelect Front AUX Input SET ModeEdit To Or From Another 56 ENMake Connections EditingSET RECORDER’S Input Mode OUTPUT1 SettingSelect Edit for PIC Start PlayerSET Input Mode Audio Dubbing58 EN VHS Audio DubbingEND Audio Dubbing Insert Editing DV Insert Editing SP Mode OnlyVHS Insert Editing Reset the Counter Engage Insert EditingStart Editing END Insert EditingConnecting To a Video Titler Connecting To a Printer Digital printerSET Remote Control Mode 64 ENTurn on the TV SET TV Brand CodeCable Box Multi-Brand Remote Control Turn on the Cable BOXOperate Cable BOX Cable BOX Brand Name Brand CodeSET Remote Control DBS Receiver Multi-Brand Remote Control66 EN Turn on the DBSUnplug Vcrs Power Plug in Power CordTurn VCR Power on CordClear or USE Cleaning Dealer 68 ENCassette gets stuck partway Then insert the cassetteRe-perform the set-up procedures Timer againPoint is not dubbed That ‰appears on the front display PanelRe-perform the VCR Plus+ setup Procedure pg70 EN RoubleshootingQuestions and Answers EN Can the VCR indefinitely remain in the still mode?Can the VCR indefinitely remain in the Record-Pause mode? What happens if the tape runs out during recording?QDV Record Indicator pg wDisplay Panel pg Wertyu4S Video Output Connectors pg 3S Video Input Connector pg32Tape Speed Indicators pg Point the remote control toward the sensor window IndexExpress Timer Programming Plug & Play Random Assemble Editing Record Safety TabVideo Connection Tape Dubbing Tape Position Indicator List Of Terms76 EN HOW to Locate Your JVC Service Center For Servicing Only in U.S.AWarranty Only in U.S.A 78 ENMemo HR-DVS2U