Using the TV Buttons on the Remote Control
Basic Connections/Auto Setup
POWEROPEN/CLOSE
1 | 2 | 3 |
| ||
SCREEN FIT |
| TV/VCR |
| SHUTTLE |
|
MODE/ 4 | 5 | 6 |
REPEAT |
| AUDIO |
7 | 8 | 9 |
ZOOM |
| ANGLE |
3D SOUND |
| CLEAR |
TV MUTE | 0 | INPUT SEL. |
100+ | 2 | |
|
| |
DVD | VCR | SELECT TV |
3
VIEW
DIGEST | + |
|
| DISPLAY |
| VOL |
| CH/TRK |
|
F.ADV/SKIP | - |
|
|
|
3 |
|
|
|
|
DVD |
| VCR | SELECT | TV |
| VIEW |
|
|
|
| 4 |
|
|
|
DIGEST | + |
|
| DISPLAY |
| VOL |
| CH/TRK |
|
F.ADV/SKIP | - |
|
|
|
| 4 |
|
|
|
REC |
|
|
| DISC MENU |
7 |
| 8 | 9 | |
ZOOM |
|
|
| ANGLE |
3D SOUND |
| CLEAR | ||
TV |
| 0 |
| INPUT SEL. |
|
|
|
| |
5 |
| VCR | SELECT | TV |
| VIEW |
|
|
|
DIGEST | + |
|
| DISPLAY |
| VOL | CH/TRK |
| |
F.ADV/SKIP | - |
|
|
|
Your VCR remote control will work with Samsung televisions and compatible brands.
To determine whether your television is compatible, follow the instructions below.
1Switch your television on.
2Point the remote control towards the television.
3Hold down the TV button and enter the
Brand | Codes | Brand | Codes |
SAMSUNG | 01, 14, 15, 23 | LOEWE | 28 |
SHARP | 02, 16, 22 | ZENITH | 17 |
SONY | 03 | LG | 06, 08, 18 |
RCA | 07, 29 | MAGNAVOX | 04 |
TOSHIBA | 09 | EMERSON | 21 |
PANASONIC | 12, 24 | SANYO | 05, 20 |
JVC | 11 | DAEWOO | 19 |
HITACHI | 10 | NOBLEX | 25 |
MITSUBISHI | 13 | TELEFUNKEN 26 | |
NEWSAN | 27 |
|
|
|
|
|
|
Result: If your television is compatible with the remote control, it will switch off. It is now programmed to operate with the remote control.
➢If several codes are indicated for your television brand, try each one in turn until you find one that works.
☛When you change the batteries in the remote control, you must reprogram the code, following the same procedure.
You can then control the television using the following buttons.
Button | Function |
|
|
POWER ➀ | Used to switch the television on and off. |
|
|
INPUT ➁ | Used to select an external source. |
In this section, you will connect the
NOTES:
•Advanced Connections are covered in Appendix A.
•Even if you plan to use the
either the standard RF or the Line Out connection. This enables you to operate the
1 Connect Antenna/Cable to |
Connect the RF antenna cable from your indoor/outdoor antenna or |
cable wall outlet to the IN (FROM ANT.) jack on the back panel of |
the |
2 Connect |
Choose one of the following methods to connect the |
your TV: |
RF Connection |
Connect the supplied RF antenna cable from the OUT (TO TV) jack |
on the back panel of the |
Input. |
NOTE : Check the channel to connect |
television’s Antenna Input; See page 22. |
Line Connection |
Connect an |
the LINE OUT jacks on the back panel of the |
television’s Line In jacks. Use red for right audio, white for left |
audio, and yellow for video. |
NOTE: It is recommended that you use the Line Connection if your |
TV is equipped with RCA jacks. |
3 Plug In |
Connect the |
outlet. Don’t press any buttons on the |
auto setup. “AUTO” blinks while the |
procedure, where it will automatically search for all active channels |
and set the clock. When Auto setting has been completed, the front |
panel displays the current time. If Auto Clock set is unable to find a |
channel to set the clock, you can set the clock manually; See page |
18. |
4 Turn On |
Press the POWER button on the remote control or on the |
DVD & VCR |
1 |
From Antenna or Cable |
DVD & VCR | |
| 2 |
To TV’s Antenna Input | 2 |
3
VOL + or – ➂ | Used to adjust the volume of the television. |
|
|
CH ("or ❷) ➃ | Used to select the required channel. |
|
|
MUTE ➄ | Used to toggle the sound on and off. |
➢The various functions will not necessarily work on all televisions. If you encounter problems, operate the television directly.
5 | Turn On TV |
| Press the POWER button on your TV. |
|
|
6 | Set TV to Channel 3, 4 or Line |
| Be sure to use the same channel you selected in Step 2. If you |
| used the Line Connection, set your TV to its Line Input. |
|
|
POWER |
4 |
POWER
| 4 |
| 2 |
SCREEN FIT |
|
| SHUTTLE |
MODE/ 4 | 5 |
REPEAT |
|
7 | 8 |
ZOOM |
|
3D SOUND | CL |
12
13