Goodman Mfg IO-367B Unit Location, ALL Installations, Ground Level Installations only

Page 4

UNIT LOCATION

WARNING

TO PREVENT POSSIBLE EQUIPMENT DAMAGE, PROPERTY DAMAGE, PERSONAL INJURY OR DEATH, THE FOLLOWING BULLET POINTS MUST BE OBSERVED WHEN INSTALLING THE UNIT.

IMPORTANT NOTE: Remove wood shipping rails prior to installation of the unit. See important note under Roof Curb Installation Only.

ALL INSTALLATIONS:

IMPORTANT NOTE: Unit should be energized 24 hours prior to compressor start up to ensure crankcase heater has sufficiently warmed the compressors. Compressor dam- age may occur if this step is not followed.

NOTE: Appliance is shipped from factory for vertical duct application.

Proper installation of the unit ensures trouble-free operation. Improper installation can result in problems ranging from noisy operation to property or equipment damages, danger- ous conditions that could result in injury or personal property damage and could void the warranty. Give this booklet to the user and explain it’s provisions. The user should retain these instructions for future reference.

•For proper operation and condensate drainage, the unit must be mounted level.

•The flue outlet hood must be at least three feet above any forced air inlet located within ten feet. The economizer/manual fresh air intake/motorized fresh air intake and combustion air inlet mounted on the unit are not affected by this restriction.

•Do not locate the unit in an area where the outdoor air (i.e. combustion air for the unit) will be frequently contaminated by compounds containing chlorine or fluorine. Common sources of such compounds include swimming pool chemicals and chlorine bleaches, paint stripper, adhesives, paints, varnishes, sealers, waxes (which are not yet dried) and solvents used during construction and remodeling. Various commercial and industrial processes may also be sources of chlorine/ fluorine compounds.

•To avoid possible illness or death of the building occupants, do NOT locate outside air intake device (economizer, manual fresh air intake, motorized fresh air intake) too close to an exhaust outlet, gas vent termination, or plumbing vent outlet. For specific distances required, consult local codes.

•Allow minimum clearances from the enclosure for fire protection, proper operation, and service access (see Unit Clearances). These clearances must be permanently maintained.

•When the unit is heating, the temperature of the return air entering the unit must be between 50°F and 100°F.

GROUND LEVEL INSTALLATIONS ONLY:

•When the unit is installed on the ground adjacent to the building, a level concrete (or equal) base is recommended. Prepare a base that is 3” larger than the package unit footprint and a minimum of 3” thick.

•The base should also be located where no runoff of water from higher ground can collect in the unit.

ROOF TOP INSTALLATIONS ONLY:

•To avoid possible property damage or personal injury, the roof must have sufficient structural strength to carry the weight of the unit(s) and snow or water loads as required by local codes. Consult a structural engineer to determine the weight capabilities of the roof.

•The unit may be installed directly on wood floors or on Class A, Class B, or Class C roof covering material.

•To avoid possible personal injury, a safe, flat surface for service personnel should be provided.

•As indicated on the unit’s data plate, a minimum clearance of 36” to any combustible material is required on the access side of the unit. All combustible materials must be kept out of this area.

•This 36” clearance must also be maintained to insure proper combustion air flow. The combustion air intake must not be blocked for any reason, including blockage by snow.

•Adequate clearances from the unit to any adjacent public walkways, adjacent buildings, building openings or openable windows must be maintained in accordance with National Codes.

UNIT PRECAUTIONS

•Do not stand or walk on the unit.

•Except for holes in the wiring entrances (see Figure below), do not drill holes anywhere in panels or in the base frame of the unit. Unit access panels provide structural support.

ELECTRICAL ENTRANCE LOCATIONS

•Do not remove any access panels until unit has been installed on roof curb or field supplied structure.

•Do not roll unit across finished roof without prior approval of owner or architect.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents 15 & 20 TON CPC Replacement Parts Safety InstructionsTo the Installer High VoltagePRE-INSTALLATION Checks General InformationEPA Regulations National CodesALL Installations Ground Level Installations onlyRoof TOP Installations only Unit PrecautionsBefore installing this unit Roof Curb Installations onlyClearances Roof Curb POST-INSTALLATION ChecksRoof TOP Duct Connections Rigging Details Two spreader bars must span over the unit to preventData Electrical WiringRigging Removal Units Installed on Roof Tops LOW Voltage Control WiringCirculating AIR and Filters STARTUP, ADJUSTMENTS, and ChecksVenting Condensate Drain Connection Moving Machinery Hazard Tension and Alignment Adjustment Evaporator FAN Rotation Check Three Phase Models onlyField Duct Connections Filter Section CheckAIR Flow Adjustments START-UP Procedure and ChecklistRefrigeration System Checks Final System ChecksMotor Sheave Adjustments MaintenanceService Clean Outside Coil Qualified Servicer onlyCONDENSER, EVAPORATOR, and Induced Draft Motors LubricationTurns Open CFM BHPAppendix a Blower Performance Data Belt Drive High Static Models RLA LRARLA FLA BD STD StaticAppendix C Unit Dimensions Goodman Manufacturing Company, L.P

IO-367B specifications

Goodman Manufacturing, a well-respected name in the HVAC industry, offers an impressive range of products tailored to enhance energy efficiency and comfort in residential environments. Among their standout offerings is the IO-367B model, a heat pump designed to deliver exceptional performance, reliability, and user-friendly features.

The Goodman IO-367B is a split system heat pump that provides both heating and cooling capabilities, making it a versatile choice for homeowners looking to maintain an optimal indoor climate year-round. Its sleek design allows for easy installation and integration into existing systems, ensuring minimal disruption during the setup process.

One of the key features of the IO-367B is its energy efficiency. With a high SEER (Seasonal Energy Efficiency Ratio) rating, it operates smoothly and effectively while keeping energy consumption low. This not only leads to lower utility bills for homeowners but also supports environmentally friendly practices by reducing the overall carbon footprint. The unit is compliant with the latest energy regulations, making it a future-proof investment for those who prioritize sustainability.

The IO-367B employs advanced technology, including a multi-speed compressor that adjusts operation to meet the specific heating or cooling demands of a space. This feature enhances comfort by reducing temperature fluctuations and maintaining a consistent climate. Additionally, its sound-dampening features ensure quieter operation, making it an excellent choice for both indoor and outdoor installations.

Other notable characteristics include the durable construction of the heat pump, which is designed to withstand varying weather conditions. Its corrosion-resistant cabinet enhances longevity and reliability, ensuring that homeowners can depend on their system for years. Furthermore, Goodman provides a generous warranty on the IO-367B, reflecting their confidence in the product’s durability and performance.

In conclusion, the Goodman IO-367B heat pump stands out in the market due to its energy efficiency, advanced technology, and sturdy design. Ideal for those seeking to enhance their home's comfort while being mindful of energy consumption, this model is a reliable solution for heating and cooling needs.
Top Page Image Contents