1031A Operating Manual
AUDIO PRECISION 1031anec LEVEL(dBr) | vs FREQ(Hz) | 07 SEP 93 11:21:58 | AUDIO PRECISION 1031anec LEVEL(dBr) | vs FREQ(Hz) | 07 SEP 93 10:04:11 | |||||
100 |
|
|
|
|
| 110 |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
95 |
|
|
|
|
| 105 |
|
|
|
|
90 |
|
|
| 0° |
| 100 |
|
|
|
|
|
|
| 15° |
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| |
85 |
|
|
|
|
| 95 |
|
|
|
|
80 |
|
|
|
|
| 90 | BASS TILT |
| TREBLE TILT |
|
|
|
|
|
|
|
|
|
| ||
75 |
|
|
| 30° |
| 85 |
|
|
|
|
|
|
| 45° |
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| |
70 |
|
|
|
|
| 80 |
|
|
|
|
65 | 100 |
|
|
|
| 75 | BASS |
|
|
|
|
|
|
|
|
|
|
|
|
| |
60 | 95 |
|
|
|
| 70 |
|
|
|
|
| 90 |
|
|
|
| 65 |
|
|
|
|
| 20 | 100 | 1k | 10k | 20k | 60 | 100 | 1k | 10k | 20k |
| 20 | |||||||||
Figure 4. The upper curve group shows the horizontal directivity characteristics of the 1031A in vertical configuration measured at 1 m. The lower curve is a 1/3 octave band power response, measured in an IEC approved reverberation chamber.
Figure 5. The curves show the effect of the bass tilt, treble tilt and bass roll-off controls on the free field response.
SYSTEM SPECIFICATIONS |
| CROSSOVER SECTION |
| AMPLIFIER SECTION |
|
Lower | < 47 Hz | Input connector XLR female: | pin 1 gnd | Bass amplifier short term output power with a | |
Upper | > 22 kHz |
| pin 2 + | 8 Ohm load: | 120 W |
|
|
| pin 3 - |
|
|
Free field frequency response of system: 48 Hz - 22 kHz (± 2 dB)
Maximum short term sine wave acoustic output on axis in half space, averaged from 100 Hz to 3 kHz:
@1m > 110 dB SPL
@0.5m > 116 dB SPL
Maximum long term RMS acoustic output in same conditions with IEC weighted noise (limited by driver unit protection circuit):
@1m > 101 dB SPL
@0.5m > 107 dB SPL
Maximum peak acoustic output per pair above console top, @ 1 m from the engineer with music
material: | > 120 dB |
Self generated noise level in free field @ 1m
on axis: < 10 dB
Harmonic distortion at 90 dB SPL @ 1m on axis:
Freq: | 50...100 Hz | < 3% |
| > 100 Hz | < 0.5% |
Drivers: Bass 210 mm (8") cone Treble 19 mm (3/4") metal dome
Both drivers are magnetically shielded.
Weight: 12,7 kg (28 lb)
Dimensions:
Height 393 mm (15 1/2")
Width 250 mm ( 9 7/8")
Depth 290 mm (11 7/16")
Input impedance: | 10 kOhm balanced |
Input level for 100 dB SPL output @ 1m: variable from +6 to
Input level for maximum short term sine wave output of 110 dB SPL @ 1m:
variable from +16 to +4 dBu
Subsonic filter below 45 Hz : | 18 dB/octave |
Ultrasonic filter above 25 kHz: | 12 dB/octave |
Crossover frequency, Bass/Treble: | 2.2 kHz |
Crossover acoustical slopes: | 24 dB/octave |
Treble tilt control operating range in 2 dB steps: from +2 to
Bass
Bass tilt control operating range in 2 dB steps: from 0 to
The 'CAL' position is with all tone controls set to 'off' and the input sensitivity control to maximum (fully clockwise).
Treble amplifier short term output power with an
8 Ohm load: | 120 W |
Long term output power is limited by driver unit protection circuitry.
Amplifier system distortion at nominal output:
| THD | < 0.05% |
|
| < 0.05% |
|
| < 0.05% |
| DIM 100 | < 0.05% |
Signal to Noise ratio, referred to full output: | ||
| Bass | > 100 dB |
| Treble | > 100 dB |
Mains voltage: | 230, 100/200 or 115/230V | |
| according to region | |
Voltage operating range: | ±10% | |
Power consumption: | Idle | 30 VA |
| Full output | 160 VA |
Genelec Document D1031AR001 Copyright Genelec Oy 6.2003. All data subject to change without prior notice
International enquiries:
Genelec, Olvitie 5
Phone +358 17 83881
Fax +358 17 812 267
Email genelec@genelec.com
| www.genelec.com |
In the U.S. please contact: | In China please contact: |
Genelec, Inc., 7 Tech Circle | Genelec China Representative Office |
Natick, MA 01760, USA | Soho New Town, 88 Jianguo Road |
Phone +1 508 652 0900 | |
Fax +1 508 652 0909 | Beijing 100022, China |
Email genelec.usa@genelec.com | Phone +86 10 8580 2180 |
| Fax +86 10 8580 2181 |