HOW to Operate

English

ACCESSORIES (Fig.1)

TO ASSEMBLE HOSE (Fig. 2)

TO ATTACH HOSE (Fig. 3)

RUG AND FLOOR TOOL (Fig. 6) (for CV-S890)

RUG AND FLOOR TOOL (Fig. 21)

ELECTRONIC POWER CONTROL (for CV-S890, Fig. 8)

SUCTION CONTROL (Fig. 9)

BAG FULL INDICATOR (Fig. 10)

AUTOMATIC CORD REWIND (Fig. 11)

TO USE ATTACHMENTS (Fig. 13,14)

TO STORE ACCESSORIES (Fig. 15)

TO DISCONNECT CURVED JOINT PIPE (Fig. 16)

HOW TO REMOVE DUST

TAKING OUT DUST BAG (Fig. 17)

SETTING DUST BAG (Fig. 18)

CARE OF AIR FILTERS

MOTOR PROTECTION AIR FILTER (Fig. 19)

AFlexible crush proof hose

BExtension pipe

CCurved joint pipe

DJoint pipe

ECloth bag

F	Dusting brush	5	(stored in tool
G	Crevice nozzle		storage space)

HRug and floor tool (for CV-S880, CV-T885)

IRug and floor tool (for CV-S890)

JRug and floor tool (Y31)

KRug and floor tool (D321-D)

The hose and joint pipe are packaged separately. To put them together, insert the curved joint pipe 1and joint pipe 2into each end of the hose63until the claws 4of the stopper rings 5click into the holes

of the curved joint pipe and joint pipe.

Insert the joint pipe 2into the suction inlet 7of the cleaner. When you remove the hose 3, pull the joint pipe 2while pressing the button 8.

TO ATTACH EXTENSION PIPES (Fig. 4)

Fit the extension pipes 9, and the selected suction attachment by twisting together.

TO DETACH EXTENSION PIPES (Fig. 5)

Twist and pull the extension pipe Ä, upward.

To clean smooth surfaces, depress the switch "" to in line with " " Ç. To clean rugs or carpets depress the switch "" to in line with "" Å.

The tool is fitted with a brush at the back which can either be used in the “withdrawn” or “projected” position. These positions are operated

toe. If you feel the tool is heavy to slide on the carpet, please reduce the suction power by adjusting the suction control. (Fig. 9)

ON-OFF SWITCH (Fig. 7)

Turn cleaner on or off by pushing downward on the power switch É.

Suction power may be regulated electronically using the dial on the unit Ñ. For stronger suction (thick carpets or hard floors) rotate the dial to the right. Rotate it to the left for reduced suction (curtains, delicate fabrics).

Suction pressure is reduced by moving the adjustment ring Öon the curved joint pipe 1to expose a hole.

The more hole area exposed the lower the suction.

Low suction pressure is recommended for cleaning curtains, blinds, delicate fabrics etc,.

When the orange sign Üappears in the large window continuously, change the cloth bag.

Check the bag full indicator (with the highest power of electronic power control for CV-S890) by lifting cleaning head from the surface being cleaned or removing the crevice nozzle when it has been used.

NOTE: If the cleaner is used in such a condition as the orange sign appears in the large window, air to the motor will be reduced and the motor will eventually burn out.

The power cord is stored neatly inside the cleaner using an automatic cord rewind.

When cleaning is completed unplug from the mains and depress the rewind pedal á, the cord will automatically rewind.

NOTE: Should the cord not fully rewind, pull out a short length and press the pedal again.

For smooth rewinding, turn the cord inlet toward the same direction as the cord pulled out.

TOOL STORAGE SPACE (Fig. 12)

The crevice and brush tools snap into the rear storage rack àfor safekeeping and easy access.

Hose, extension pipe and rug and floor tool can be attached in assembled condition to the cleaner by using the nozzle hook âof the rug and floor tool.

This combination allows you a space storage.

1.Place the cleaner upright.

2.Slide the nozzle hook âof the rug and floor tool into the hook supporter äat the rear of the cleaner as shown in Fig. 15.

3.Turn the hose around pipes to make it compact and stable.

NOTE: Do not hold the hose and the joint pipe to transport the cleaner.

Blockages may be cleared by separating the curved joint pipe 1 from the hose. To separate the curved joint pipe depress the two claws 4which are located in the holes on both sides of curved joint pipe 6and pull apart.

When needed, the hose collar ãcan be removed from the hose end by turning it (left-handed screw).

To re-connect push hose back into curved joint pipe and twist until two claws 4locate with holes 6.

Likewise you can disconnect the hose joint on the other end of the hose.

1.Remove the plug from the electrical outlet. Open the bag compartment lid åby pulling up the clamp ç.

2.Pull out the dust bag égently.

3.Slide off the bag clip from the dust bag and dispose of dust in the dust bag.

1.Before setting the dust bag, be sure to slide back the bag clip.

2.Place the dust bag by opening its inner lid è.

3.Position the top edges of the collar to the inner lid concave, and fit the hole at the lower edge to the guide pins êof the case.

NOTE

To avoid using the cleaner without the cloth bag, the clamp system of your cleaner prevents the bag compartment lid from being clamped when the cloth bag has not been replaced, or has not been set properly in place.

byïthe pedal on the tool marked "

" (Carpet) îand "

For cleaning rug or carpet, keep the brush in its “withdrawn”

position, i.e., with the pedal marked "

" pressed down with your

Once or twice a year, or when it becomes visibly soiled, the motor protection filter ëlocated behind the cloth bag may need cleaning.

1.Take out the cloth bag, then remove the filter from the cleaner as shown in Fig. 19 and wash in warm water.

2.After washing the filter, dry thoroughly away from direct sunlight and fit back into the cleaner.

J1861_CV-S880(E)

15/07/2004, 4:07 PM