Installation Instructions

Installation of the Giant Industries, Inc., pump is not a complicated procedure, but there are some basic steps common to all pumps. The following information is to be considered as a general outline for installation. If you have unique requirements, please contact Giant Industries, Inc. or your local distributor for assistance.

1.The pump should be installed flat on a base to a maximum of a 15 degree angle of inclination to ensure optimum lubrica- tion.

2.The inlet to the pump should be sized for the flow rate of the pump with no unnecessary restrictions that can cause cavitation. Teflon tape should be used to seal all joints. If pumps are to be operated at temperatures in excess of 1400 F, it is important to insure a positive head to the pump to prevent cavitation.

3.The discharge plumbing from the pump should be properly sized to the flow rate to prevent line pressure loss to the work area. It is essential to provide a safety bypass valve between the pump and the work area to protect the pump from pressure spikes in the event of a blockage or the use of a shut-off gun.

4.Use of a dampener is necessary to minimize pulsation at drive elements, plumbing, connections, and other system areas. The use of a dampener with Giant Industries, Inc. pumps is optional, although recommended by Giant Industries, Inc. to further reduce system pulsation. Dampeners can also reduce the severity of pressure spikes that occur in systems using a shut-off gun. A dampener must be positioned downstream from the unloader.

IMPORTANT OPERATING CONDITIONS Failure to comply with any of these condi-

tions invalidates the warranty

1.Prior to initial operation, add oil to crankcase so that oil level is between the two lines on the oil dipstick. DO NOT OVERFILL. SAE 80 or SAE 90 Industrial Gear oil may be used. Crankcase oil should be changed after the first 50 hours of operation, then at regular intervals of 500 hours or less depending on operating conditions.

5.Crankshaft rotation on Giant Industries, Inc. pumps should be made in the direction designated by the arrows on the pump crankcase. Reverse rotation may be safely achieved by following a few guidelines available upon request from Giant Industries, Inc. Required horsepower for system operation can be obtained from the charts on pages 3-5.

6.Before beginning operation of your pumping

system, remember: Check that the crankcase and seal areas have been properly lubricated per recom- mended schedules. Do not run the pump dry for extended periods of time. Cavitation will result in severe damage. Always remember to check that all plumbing valves are open and that pumped media can flow freely to the inlet of the pump.

Finally, remember that high pressure operation in a pump system has many advantages. But, if it is used carelessly and without regard to its potential hazard, it can cause serious injury.

2.Pump operation must not exceed rated

pressure, volume, or RPM. A pressure relief device must be installed in the discharge of the system.

3.Acids, alkalines, or abrasive fluids cannot be pumped unless approval in writing is obtained before operation from Giant Industries, Inc.

4.Run the pump dry approximately 10 seconds to drain the water before exposure to freezing temperatures.

NOTE: Contact Giant Industries for Service School Information. Phone: (419)-531-4600

GP5132 specifications

The Giant GP5132 is a versatile and innovative bicycle designed for cycling enthusiasts who seek quality and performance. This model exemplifies the craftsmanship and cutting-edge technology that Giant is known for, making it an excellent choice for both casual riders and serious competitors.

One of the standout features of the Giant GP5132 is its lightweight frame, constructed from high-grade aluminum alloy. This material not only reduces the overall weight of the bike but also enhances its durability, allowing it to withstand the rigors of daily use and challenging terrains. Additionally, the frame geometry is carefully designed to provide optimal stability and handling, ensuring a smooth ride regardless of the conditions.

The GP5132 is equipped with a precision-engineered drivetrain system that offers a wide range of gears, allowing riders to effortlessly tackle both steep climbs and flat roads. The inclusion of high-quality components ensures seamless shifting and reliable performance, making it an excellent option for both commuting and long-distance rides.

Another key characteristic of the Giant GP5132 is its suspension system. With front suspension forks designed to absorb shocks and bumps, the bike offers superior comfort and control on uneven surfaces. This feature is particularly beneficial for riders who frequent rough trails or adventure routes, as it ensures that they maintain stability and confidence throughout their journey.

The GP5132 also prioritizes rider safety and visibility. Equipped with reflective accents and optional integration for lights, this model ensures that cyclists remain visible in low-light conditions. The reliable braking system, featuring hydraulic disc brakes, provides excellent stopping power, giving riders confidence in their ability to control their speed in various weather conditions.

In summary, the Giant GP5132 is a well-rounded bicycle that incorporates advanced technologies and features aimed at enhancing the overall riding experience. From its lightweight and durable frame to its efficient drivetrain and responsive suspension, this model caters to the diverse needs of cyclists. Whether navigating city streets or exploring mountain trails, the Giant GP5132 stands out as a reliable and high-performing choice.