Starting and Adjusting the Pump

Operation

WARNING

To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure on page 9.

See the Typical Installation on page 6. Be sure the air regulator (E) and bleed-type master air valve (D) are closed. Do not install the spray tip yet.

Mount the pump on the supply drum. On bung-style drums, open the vent plug to prevent a vacuum from forming in the drum. Hold a metal part of the spray gun

(M)firmly to the side of a grounded metal pail and hold the trigger open. Then open the pump’s bleed-type master air valve (D). Now slowly open the air regulator until the pump starts, about 40 psi (280 kPa, 2.8 bar).

Cycle the pump slowly until the air is pushed out and the pump and hoses are fully primed. Release the spray gun trigger and engage the safety latch. The pump should stall against pressure when the trigger is released.

Relieve the pressure, then install the spray tip in the gun.

With the pump and lines primed, and with adequate air pressure and volume supplied, the pump will start and stop as the spray gun is opened and closed. In a circulating system, the pump will run continuously and will speed up or slow down as supply demands until the air supply is shut off.

Use an adequately sized air regulator (E) to control the pump speed and the fluid pressure. Always use the lowest air pressure necessary to get the desired results. Higher pressures waste fluid and cause pre- mature wear of the packings and spray tip.

WARNING

To reduce the risk of overpressurizing your system, which could result in component rupture and cause serious injury, never exceed the Maximum Incom- ing Air Pressure given on your pump or in the Technical Data on pages 22 and 24.

Keep the packing nut/wet-cup (14) filled with Graco Throat Seal Liquid (TSL) or compatible solvent, to help prolong the packing life. Adjust the packing nut weekly so it is just tight enough to prevent leakage; do not overtighten. See Fig. 2. Always relieve the pressure before adjusting the packing nut.

Never allow the pump to run dry of the fluid being pumped. A dry pump will quickly accelerate to a high speed, possibly damaging itself. A pump runaway valve (B), which shuts off the air supply to the pump if the pump accelerates beyond the pre-set speed, is available. If your pump accelerates quickly, or is run- ning too fast, stop it immediately and check the fluid supply. If the supply container is empty and air has been pumped into the lines, refill the container and prime the pump and the lines with fluid, or flush and leave it filled with a compatible solvent. Be sure to eliminate all air from the fluid system.

Shutdown and Care of the Pump

WARNING

To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure on page 9.

For overnight shutdown, relieve the pressure. Always stop the pump at the bottom of the stroke to prevent the fluid from drying on the exposed displacement rod and damaging the throat packings.

Always flush the pump before the fluid dries on the displacement rod. Relieve the pressure after flushing.

10 308118

224348, 223540, 256714, 256713 specifications

Graco is a reputable name in the realm of paint sprayers and other painting equipment, providing quality solutions for both professional and DIY users. Among their popular products are the models Graco 256714, 223540, 224348, and 256713. Each unit boasts unique features tailored to enhance efficiency, performance, and quality in painting applications.

The Graco 256714 is renowned for its versatility and ease of use. It is ideal for small to medium-sized projects, offering a powerful motor that ensures a consistent spray pattern. This model features an adjustable pressure control, allowing users to customize the flow rate according to the specific paint type and project needs. It also comes equipped with a flexible suction tube, enabling users to spray directly from a 1-gallon or 5-gallon paint bucket without the hassle of frequent refills.

Next in line is the Graco 223540, known for its lightweight design and portability. This unit integrates an innovative EasyPrime feature, allowing for easy priming and quick setup. It's particularly favored for its ability to handle a variety of coatings, from stains to thick latex paints. The 223540 model is user-friendly, making it an excellent choice for beginners or those looking for an efficient solution for home improvement projects.

The Graco 224348 takes things a step further with advanced airless technology which allows for smooth, even finishes without roller marks or brush strokes. This model is equipped with a PowerFlush cleaning system that simplifies the cleaning process, saving time and effort after painting tasks. It is also designed with a professional-grade hose that ensures durability and flexibility for accessing tight spaces.

Finally, the Graco 256713 model is designed for the more demanding projects. It offers high-output performance suitable for extensive jobs while maintaining a lightweight structure for ease of handling. One of its standout features is the QuietTech technology, which reduces noise without compromising on power. This model is equipped with a robust motor and offers a wide range of spray tips, making it adaptable for various surfaces and textures.

In summary, these Graco models share a commitment to delivering high-quality performance, portability, and user-friendly features. Whether you are tackling a small home project or a larger professional job, Graco's innovations in spray technology cater to a range of painting needs, making them a solid investment for both amateurs and experts alike.