English | Controls/Power Supply |
Power Supply
General operation
Top and front panels (See 1)
1VOLUME – to adjust volume level
2Source selector : CD,TUNER,
TAPE/POWER OFF
– selects CD, tuner or tape source of sound
–power off switch
3CD door
4TUNING – tunes to radio stations
5BAND – selects waveband
6PREVIOUS, NEXT ° , ¤
– skips or searches a passage/track backwards or forward
7PROG – programs and reviews programmed track numbers
8Cassette recorder keys:
; – pauses playback or recording
9/ – stops the tape;
– opens the cassette holder
5or 6 – fast rewinds/ winds tape
2– starts playback
0– starts recording
9Cassette door
0CD Display – shows the CD functions
!PLAY/PAUSE 2; - starts or pauses CD playback.
@STOP 9 – stop playback;
–erases a CD program.
Back panel
#Telescopic antenna - improves FM reception.
Note: MW band antenna is built into set (see Tuner reception)
$Battery door - open to insert 6 x 1.5V
%AC POWER/MAINS - inlet for power cord.
CAUTION
Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation.
This set complies with the radio interference requirements of the European Community.
Power Supply
Whenever convenient, use the mains supply cord if you want to conserve battery life. Make sure you remove the plug from the set and wall outlet before inserting batteries.
Batteries (not included)
1Open the battery compartment and insert six batteries, type
2Replace the compartment door, making sure the batteries are firmly and correctly in place. The set is now ready to operate.
Batteries contain chemical substances, so they should be disposed of properly.
Incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst:
•Do not mix battery types: e.g. alkaline with carbon zinc. Only use batteries of the same type for the set.
•When inserting new batteries, do not try to mix old batteries with the new ones.
•Remove the batteries if the set is not to be used for a long time.
Using AC Mains
1Check if the power/mains voltage, as shown on the type plate located on the bottom of the set, corresponds to your local power supply. If it does not, consult your dealer or service center.
2Connect the power cord to the AC POWER/MAINS inlet and the wall socket.The mains lead is now connected and ready for use.
3To switch the set off completely, withdraw the power cord from the wall socket.
•Disconnect the mains lead from the wall socket to protect your set during heavy thunderstorms.
The type plate is located on the bottom of the set.
For users in the U.K., please follow the boxed instructions ‘Important notes...’ on this sheet.
Switching POWER on/off: Save energy
To avoid unnecessary energy consumption, always adjust the source selector to TAPE/POWER OFF after using the set. Also check that the tape deck keys are released.
General operation
1To select your sound source adjust the source selector to : CD, TUNER or
TAPE/POWER OFF.
2Adjust the sound with the VOLUME control.
3To switch off the set, adjust the source selec- tor to TAPE/POWER OFF position and check the cassette keys are released.
Tuner reception
1Adjust the source selector to TUNER.
2Adjust BAND to select your desired wave- band.
3Turn TUNING to tune to a station.
•For FM band signals, extend and turn the telescopic antenna for best reception. Reduce its length if the signal is too strong.
•For MW (AM or LW) band signals, the set uses a
4To switch off the radio, adjust the source selector to TAPE/POWER OFF position and check the cassette keys are released.
CD Player
Display indication for CD
functions:
–OP: (See 2) CD door open
–
–During CD playback: 2 and current track number
–2;: (See 4) playback on pause