CD Player
CD Player | Cassette Recorder |
| • | Press ° once briefly to return to the begin- |
– prog: when CD program is active |
| ning of a current track. |
– Fu: program memory full | • | Press ° repeatedly for a previous track. |
|
4 Repeat steps 2 to 3 to select and store all |
desired tracks in this way. |
➜ Fu indicates the program memory is full |
(when you have stored tracks on all 32 |
program locations). |
General information on recording
• Recording is permissible insofar as copyright |
or. other rights of third parties are not |
infringed. |
Playing a CD
This CD player plays Audio Discs including
•
1Adjust the source selector to CD.
2Insert a CD/
3Press PLAY/PAUSE 2; on the set to start playback.
4To pause playback press PLAY/PAUSE 2;. Press PLAY/PAUSE 2; again to resume play.
5To stop CD play, press STOP 9.
6To switch off the set, adjust the source selector to TAPE/POWER OFF position and check the cassette keys are released.
Note : CD play will also stop when:
-you open the CD compartment;
-you select TUNER or TAPE/POWER OFF sound source;
-the CD has reached the end of playback.
Selecting a different track
During playback you can use ° / ¤ to select
a particular track.
-If you have selected a track number in the stop or pause position, press PLAY/PAUSE 2; to start playback.
•Press ¤ once briefly for the next track, or press repeatedly until the desired track num- ber appears in the display.
Finding a passage within a track
1During playback, press and hold down ° / ¤.
•The CD is played at high speed and low vol- ume.
2When you recognize the passage you want release ° / ¤.
•Normal playback resumes.
Note : When searching within a final track and you reach the end of the last track, the CD goes to stop mode.
Programming track numbers
You may store up to 32 tracks in the desired sequence. If you like, store any track more than once.
1In the stop position, press PROG to activate programming.
➜Display shows 1 indicating the start of the program. prog flashes. (See 5)
2Press ° or ¤ to select your desired track number.
3Press PROG to store the desired track number.
➜Display shows your desired track number briefly followed by a number, 2 (up to 32 in sequence) indicating the next program location available. (See 6)
5 To play your program, press PLAY/PAUSE |
2;. |
To review a program
•In the stop position, press PROG repeatedly to see your stored track numbers.
Erasing a program
You can erase the contents of the memory by:
–selecting TUNER or TAPE/POWER OFF sound source;
–opening the CD door;
➜Display: prog disappears.
Cassette playback
1Adjust the source selector to
TAPE/POWER OFF.
2Press 9/ to open the cassette holder and insert a cassette and close the deck.
3Press 2 to start playback.
4To pause playback press ;. To resume, press the key again.
5By pressing 5 or 6 , fast winding of the tape is possible in both directions. To stop fast winding, press 9/
6To stop the tape, press 9/.
The keys are automatically released at the end of a tape and the set switched off (unless PAUSE mode ; has been activated.)
• For recording, use only NORMAL type cas- |
settes (IEC type I) on which the tabs have not |
yet been broken.This deck is not suited for |
recording on CHROME (IEC II) or METAL |
(IEC IV) type cassettes. |
• The best recording level is set automatically. |
Altering the VOLUME will not affect the |
recording. |
• To protect a tape from accidental erasure, |
break out the tabs. If you wish to record |
again, cover the tabs with a piece of adhesive |
tape. |
Synchro Start CD recording
1Select CD source.
2Insert a CD and if desired, program track numbers.
3Press 9/ to open the cassette holder. Insert a blank tape and close the deck.
4Press 0 to start recording.
➜Playing of the CD program starts auto- matically from the beginning of the pro- gram. It is not necessary to start the CD player separately.
5For brief interruptions press ;. To resume recording, press ; again.
6To stop recording, press 9/.