English | CONTROLS / POWER SUPPLY |
|
CONTROLS ( see figure 1 ) |
1 OPEN 2 | opens the CD lid |
2 | 2; | switches the player on, starts or pauses CD play |
3 | 9 | stops CD play, clears a program or switches the player off |
4 | § | skips and searches CD tracks forwards |
5 ESP | EXTREME SHOCK PROTECTION ensures continuous CD play- |
| | back regardless of vibrations and shocks |
6 MODE | selects the different playing possibilities: SHUFFLE, |
| | SHUFFLE REPEAT ALL, REPEAT, REPEAT ALL and SCAN |
7............................display
8 PROGRAM | ..........programs tracks and reviews the program |
9 BASS | switches the bass enhancement on and off. This button also |
| switches acoustic feedback (the beep) on/off when it is |
| pressed for more than 2 seconds |
0 ∞ | skips and searches CD tracks backwards |
! RESUME | stores the last position of a CD track played |
HOLD | locks all buttons |
OFF | switches RESUME and HOLD off |
@LINE OUT/p........3.5 mm headphone socket, socket to connect the player to another audio input of an additional appliance, remote control socket (not on all versions)
#VOL E ............adjusts the volume
$ 4.5V DC | ...............socket for external power supply |
%............................belt clip holder
^............................typeplate
This set complies with the radio interference requirements of the
European Community.
Batteries (supplied or optionally available)
You can use the following batteries with this CD-player:
•normal batteries type LR6, UM3 or AA (preferably Philips), or
•alkaline batteries type LR6, UM3 or AA (preferably Philips).
Notes:– Old and new or different types of batteries should not be combined.
–Remove batteries if they are empty or if the player is not going to be used for a long time.
Inserting batteries
1 Push OPEN 2 to open the CD lid.
2 Open the battery compartment and insert either 2 normal or alkaline batteries, or the rechargeable NiMH battery AY3362 (if supplied).
Battery indication
The approximate power level of your batteries is shown in the display.
Battery full
Battery two-thirds full
Battery one-third full
Battery dead or empty. When the batteries are dead or empty, the symbol A flashes, bAtt is displayed, and the beep tone sounds repeatedly.
Average playing time of batteries under normal conditions
Battery type | ESP on | Power Save |
Normal | 5 hours | 6 hours |
Alkaline | | 22 hours | 25 hours |
Rechargeable ECO-PLUS NiMH battery | 9 hours | 10 hours |
Batteries contain chemical substances, so they should be disposed of properly.
POWER SUPPLY / GENERAL INFORMATION
ECO-PLUS NiMH battery information (for versions supplied with the rechargeable ECO-PLUS NiMH battery AY 3362)
Recharging works only on players supplied with the rechargeable ECO-PLUS NiMH battery AY 3362.
Recharging the ECO-PLUS NiMH battery on board
1Insert the rechargeable ECO-PLUS NiMH battery AY 3362.
2Connect the mains adapter to the 4.5V DC socket of the player and then to the wall socket.
y 
is pulsing.
•Recharging stops after a maximum of 7 hours, or when you start playback.
3When the battery is fully recharged, 
and FULL appear briefly in the display,
before the display switches off.
Notes: – It is normal for the batteries to become warm during recharging.
–If the batteries become too warm, recharging will be interrupted for approximately 30 minutes and Hot is displayed.
–To ensure proper recharging on board, take care that contacts are clean.
–Use only the ECO-PLUS NiMH battery AY 3362.
Handling instructions
•Recharging already charged or half-charged batteries will shorten their lifetime. We therefore recommend that you let the rechargeable ECO-PLUS NiMH battery run till it is completely empty before you recharge it.
•To avoid a short circuit, do not let the battery touch any metal object.
•If the battery becomes empty soon after recharging, then either its contacts are dirty or it has reached the end of its lifetime.
Mains adapter (supplied or optionally available)
Use only the AY 3170 adapter (4.5 V / 300 mA direct current, positive pole to the center pin). Any other product may damage the player.
1 Make sure the local voltage corresponds to the power adapter’s voltage.
2Connect the power adapter to the 4.5V DC socket of the player and to the wall socket.
Note: Always disconnect the adapter when you are not using it.
Belt Clip (not on all versions)
1To attach the belt clip to the CD-player, position the
| shaped grip (found on the back of the belt clip) so | BELT CLIP |
| that it fits into the belt clip hole of the CD-player. | |
2 | Turn the clip to LOCK as indicated on the set. | |
3 | To detach, gently lift the belt clip and turn | |
| to RELEASE as indicated on the set. | |
LOCK
LIFT
RELEASE
Environmental information
•All redundant packing material has been omitted. We have done our utmost to make the packaging easily separable into two mono materials: cardboard (box) and polyethylene (bags, protective foam sheet).
•Your set consists of materials which can be recycled if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packing materials, exhausted batteries and old equipment.
