Emerson SMV300 Preparation for USE, Unpacking and Setup, Speaker Connection See figure

Page 3
Power Sources
To Right Speaker
Figure 1
To Left Speaker

SMV300 O/M.QXD 6/21/01 7:46 AM Page 2

PREPARATION FOR USE

Unpacking and Setup

•Carefully remove the unit from the display carton and remove all packing material from the unit itself.

•Remove any descriptive labels that may be found on either the front or top cabinet of the unit. Do not remove any labels located on either the back or bottom cabinet of the unit.

Speaker Connection (See figure 1)

1.Place the speakers in convenient locations on either side of the unit. Usually a distance of three to five feet between speakers provides the

best stereo effect, but this may vary depending on the size and acoustics of the room.

2. Locate the Speaker Terminals on the rear of the unit and connect the red and black wires to the red and black terminals, coordinating the

color.

3. To connect the speakers, press the terminal down, insert the speaker wire and release the terminal.

4. Pull lightly on the connection to make sure it is secure.

CAUTION: Only connect the speakers which are supplied with the unit.

The use of any other or additional speakers may cause damage to the unit. Never operate the unit without the speakers connected.

This audio system is designed to operate on 120V AC, 60Hz house current. Attempting to operate this unit from any other power source may cause damage to the unit, which is not covered by your warranty.

 

 

 

ACOutlet

AC Operation

ACPlug

Unwind the AC cord and extend it to its full length. Insert it into any

 

convenient 120V, 60 Hz household outlet.

 

Please note that this unit is equipped with a polarized AC plug which has one

 

blade wider than the other. This is a safety feature to reduce the likelihood of

 

electric shock. This polarized AC plug will only fit in a polarized AC outlet. If

Figure 2

 

 

 

 

you find that you cannot insert this plug into your outlet, you may have an obsolete non-polarized outlet. Please do not try to defeat this safety feature by using a non-polarized adapter or by filing the wider blade to make it fit into your outlet. If this plug does not fit into your outlet, you should contact a qualified licensed electrician to replace your obsolete outlet.

Ready To Switch On

Turn the power on and press the CD/SELECT Function button. Then, press the CD DOOR OPEN/CLOSE button to open the CD compartment doors. NOTE: There is a card in each of the CD compartments which is intended to prevent the CD pickup from moving during shipment of the product. Remove these cards from the CD compartments before use.

Leave 3 inches on either side so doors can open without obstruction.

This unique system also will open the CD doors if you place your hand in front of the CD2 area as shown in figure 3. After the power is on, wait for a few seconds until the unit searches the discs. Move your hand slowly towards the CD2 area parallel to the front.

Palm

Sensor

Figure 3

2

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Vertical 3 CD Player with Digital Tuning AM/FM Stereo Radio 15A250V Speaker Connection See figure Unpacking and SetupReady To Switch On Preparation for USEDigital OUT Remote Control Battery InstallationAUX Line OUTRear Location of Controls and IndicatorsRemote EQ Preset Equalizer Buttons Setting the ClockOperating Instructions Listening to the RadioHints for Better Reception Recalling Radio Presets Setting Radio PresetsNormal Playback Playing Compact Discs CD-R CompatibleCD Pause Control To Begin Playback from a Specific TrackFORWARD/REVERSE Skip Track and HIGH-SPEED Music Search Programmed Playback Repeat PlaybackChanging the Program Programmed Repeat Intro PlaybackTo Randomly Play Back a CD Instant Playback Sleep TimerTo Cancel Sleep Timer REMAIN/MODE ButtonON/OFF Timer Caring for Compact Discs Care and MaintenanceSymptom Possible Cause Solution Radio Troubleshooting GuideCall Toll Free What does this warranty cover? SCOTT, INC Limited Warranty106-01
Top Page Image Contents