Philips AJ3980AJ3980CD warranty Alarm time display, Time / Alarm, $ Alarm, Setting the Alarm Time

English CONTROLS/ INSTALLATION

SETTING THE CLOCK AND ALARM TIMES

CONTROLS (see figure 1)

1SLEEP TIMER - adjusts timer options for CD / radio

-switches CD / radio on.

2CD - starts CD playback

3RADIO - switches on radio

4TIME / ALARM

CD / RADIO OFF

-switches off CD / radio

-selects clock display

5WAKE-UP TRACK - programs your favorite CD track for wake-up track alarm.

6PUSH TO OPEN - push this corner to open CD door

7DAILY ALARM RESET - stops the active alarm for 24 hours

8+ / - VOLUME - adjusts the volume

9REPEAT ALARM/ BRIGHTNESS CONTROL

-switches off the alarm for a 9 minute period

-switches off timer function

-changes the brightness of the display window

0Main display

-shows clock time and function status

-shows radio frequency and CD track number briefly when respective function is in use

!Alarm time display - shows the alarm time and the chosen alarm activated:

-CD (AL 1 TIME), radio / buzzer (AL 2 TIME)

@ALARM 2

- selects radio / buzzer alarm

- switches radio / buzzer alarm on/ off

#Touch Screen Controls

Clock controls shown in standby mode. The radio / CD controls appear when the radio / CD is switched on. SET AL 1 - sets CD alarm time

HOUR - adjusts hour setting TIME SET - sets clock time MINUTE - adjusts minute setting SET AL 2 - sets radio / buzzer alarm

CD:

- starts / pauses CD playback

- stops CD playback

/ - skips to the next / previous CD tracks - fast search within a track

Radio:

TUNING / (up / down)

-tunes to radio stations automatically/ manually

PRESET 1 - 5 - to select / store a radio preset station

BAND - selects waveband (FM/AM).

$ALARM 1

-selects CD alarm

-switches CD alarm on/ off %p - 3.5 mm jack for headphones

^Coil antenna - improves FM reception

&Power cord

INSTALLATION (see figure 2)

AC Power Supply

1.Check if the power voltage, shown on the type plate on the bottom of the set, corresponds to your power supply. If it does not, consult your dealer or service center.

2.Connect the plug to the wall outlet.

...PH...IL..IPS scrolls across the display continuously.

•To exit the demo mode, press any button on the set.

Eg. TIME / ALARM CD / RADIO OFF

SLEEP TIMER

RADIO

CD

3.To disconnect the set completely from the power supply, withdraw the plug from the wall outlet.

Standby power consumption (clock mode)....1.5W

The serial and production number are located on the bottom of the set.

MEMORY BACKUP

The memory backup conveniently allows your clock, alarm and radio presets to be stored for up to 3 minutes when there is a power interruption e.g. AC power failure. The complete CD clock radio and display will be switched off. As soon as the power supply returns, the display will indicate the correct time.

•If power supply returns after 3 minutes, you will need to re-enter the clock and alarm time settings.

CONNECTING HEADPHONES

Connect headphones with a 3.5 mm plug into the p jack. =The built-in speaker will now be muted on the set.

DISPLAY BRIGHTNESS

In the dim / medium setting, the backlight is interactive and gently fades in and out whenever you press a touch screen control.

There are 3 settings: bright ➟ medium ➟ dim

•Press REPEAT ALARM/ BRIGHTNESS CONTROL once or more.

SETTING THE CLOCK TIME (see figure 3)

The time is displayed using the 12 hour clock where the PM indicator lights up (on = PM, off = AM).

1.In the standby mode, press TIME SET to activate the clock setting mode.

=The current clock time in the main display flashes.

2.Press HOUR / MINUTE to adjust the hours and minutes respectively.

•With your finger held down on HOUR / MINUTE, the display will increase the hours / minutes rapidly and continuously.

•Press HOUR / MINUTE briefly and repeatedly to adjust the time slowly.

3.Press TIME SET again when you have reached the correct time.

=You will hear a double beep to confirm the time setting.

SETTING THE ALARM (see figure 3)

GENERAL

Two different alarm times, ALARM 1 and ALARM 2

can be set in the CD / radio / buzzer modes.

This can be useful when for example you need to be woken up at a different time during the week and at the weekend.

SETTING THE ALARM TIME

1.In the standby mode, press ALARM 1 / ALARM 2

to select the alarm mode. Check the respective

icon appears in the display: CD radio /

buzzer .

Either press briefly:

•ALARM 1 once for CD alarm . This enables CD playback from the first track as your alarm call.

•ALARM 2 once or more for radio / buzzer

alarm.

2.Press SET AL 1 or SET AL 2 to activate the alarm setting mode.

=The current alarm time display flashes.

3.Press HOUR/ MINUTE to adjust the hours and minutes respectively.

•With your finger held down on HOUR/ MINUTE, the display will increase the hours / minutes rapidly and continuously.

•Press HOUR/ MINUTE briefly and repeatedly to

adjust the time slowly.

4.Press SET AL 1 or SET AL 2 again when you have reached the correct time.

=You will hear a double beep to confirm the time setting.

Alarm time display

If you have set both alarms, the standby alarm time display will show the alarm time which is ready to go off first, according to the current clock time.

E.g. if current clock time = 7:30

AL2 TIME = 6:20

AL 1 TIME = 7:45,

the standby alarm display shows the alarm time, 7:45.

GENTLE WAKE VOLUME

A sure way of getting up in the mornings, the gentle wake volume for the alarm begins from a fixed gentle volume (10) and gradually increases to a maximum higher setting of ( 25.)

•The default low volume is uo : 10, and the

maximum volume is uo : 25.

•During the alarm call, if you press + / - VOLUME, the volume stops automatically getting louder.