I-Data FS 250 PDS instruction manual Setup Functions supported PCL Mode, Description

Page 30

Programming via Shareport ida FS 250, Operator's Guide

8.5 Setup Functions supported (PCL Mode)

No.	Description
Y2	LPI
Y3	CPI
Y8	LU1 Language
Y10	Page Format
Y11	Paper Path
Y12	Paper Size
Y15	Baud Rate for Serial Input
Y16	Number of Data Bits for Serial Input
Y17	Parity for Serial Input
Y18	Number of Stop Bits for Serial Input
Y19	Duplex Printing
Y21	Horizontal Compression and Vertical Scaling
Y24	Interface selection
Y48	Permanent Escape Character Selection
Y51	User Defined String(s) at Power Up
Y59	Bar Code Type Definition
Y61	Setup for User Defined Strings
Y62	Setup for IBM Defined Strings
Y73	Select Translate Table
Y74	Printer Symbol Set Definition Strings
Y75	Overwrite Translate Table
Y88	Physical Margin
Y89	Physical Margin Compensation
Y90	Define User Escape String
Y91	Font Definition
Y92	Font Point Size Definition String
Y93	Font Attribute Definition String
Y94	Font Typeface Definition String
Y96	Font Change Simulation
Y97	GFID/Font Selection
Y98	Automatic Page Orientation
Y100	Printer Share String and Timer
Y119	Autoconfiguration Select
Y120	Settings Printout at Power Up
Y249	Enter Engineering Mode

TInitiate Test

T1 On-line Hex Dump

T3 ASCII Hex Dump

T4 Settings Printout

T5 Printout Translate Table

T6 Cancel ASCII Hex Dump

-30-

Image 30

Contents

EMC directive TrademarksAbout i-data September PrefaceRelated Manuals Ida FS 250 PDSTable of Contents Ida FS 250, Operators Guide Table of Contents Table of Contents Ida FS 250, Operators Guide Kit Contents Introduction to ida FS Ida FS 250 Product FeaturesIntroduction to ida FS Non-IPDSSupported Control Units IpdsEnvironment requirements Installation RequirementsPre-Installation Requirements National Language SelectionY8,number of new language% selects language Paper Size EU/US??% Option DescriptionInstallation and Connections of the ida FS Rear PanelSerial input Twinax Connector Via the Address Switch Emulation%Y37,5224% Via the LineNon-IPDS Selection Emulation Y37,3812%Upgrading to Ipds Y37,n1 Write EmulationConnecting the ida FS 250 to the Printer Connecting via Centronics outputConnecting via RS-232 output Connecting the ida FS 250 to System What if the CU Indicator fails to turn on?Testing Test via the address switchTimeout Operation of ida FS Ida FS 250 top panelPAR Parallel input SER Serial input/output Ready Printer ReadyState Indication Specifying Share Timeout and String Timeout string must be written in ONE line see example belowPage IdaSetup Ipds Programming IRQ Handling PrinterProgramming ida FS 250 non-IPDS Escape CharacterSyntax of an FSL Function RecoveryDefining a Temporary Escape Character Invalid Escape CharacterSetup Functions supported PCL Mode DescriptionESC Features Where % is the defined ESC characterNo. Description Quick Reference Guide of Supported FSL Functions Name Syntax Parameters = COR N1 Physical paper Name Syntax Parameters Ipds String Ebcdic Name Syntax Parameters IBM Gfid APO Eeprom Programming via Shareport Activating the Y249 Engineering FunctionUpdating firmware Escape sequences must be in HEXErrors and Recovery Ida FS 250 Error MessagesTwo Devices with Same Address Appendix a Use of ida FS 250 Serial Port Appendix B Test Printout Appendix C Default Gfid Table Symbol SET and Translate TableIBM Gfid Only applies to printers running PCL Level Style StrokeweightScalable Fonts Typeface PCL No Name of TypefaceFont examples Appendix D i-data Product Platform IpdsSoftware Index Programmers GuideReaders Comments