Installation
BEFORE YOU BEGIN:
1.Turn the ignition off.
2.Ensure the factory radio is turned off.
Installation |
|
1 | Gain access to the factory radio’s rear panel. The CRZNAUX2 connects directly |
to the rear panel of the factory radio. Full or partial disassembly of the dash will be |
necessary. If you are unsure of this procedure, please consult a factory service manual or have the work performed by a mobile electronics specialist. Pay special attention to warnings or instructions regarding working near airbags, other safety devices, or security systems.
2 | Connect the appropriate CRZNAUX2 harness to the factory radio. The |
CRZNAUX2 comes with two |
harness options on page 3 and compare both harnesses with the connectors on your factory radio’s rear panel. Use the harness that matches your radio’s connectors. Plug the male connector of the appropriate CRZNAUX2 harness into the matching location on the factory radio’s rear panel.
If your vehicle requires Harness Option B, shown on page 3, you must also connect the attached yellow wire. Connect the yellow wire to a constant +12V power source (vehicle battery). We DO NOT recommend the +12V constant in the factory radio harness due to the possibility of excessive voltage drop during vehicle starting.
3 | Assemble the components shown on page 2 and connect them to the |
CRZNAUX2 module. Use the diagrams on pages 2 and 3 to assemble the | |
components that will connect to and control your Zune device. | |
Power connector | wiring. Connect the black wire of the power connector shown on page 3 |
to a clean,
4 | Mount all components. Mount the CRZNAUX2 module behind or under the dash |
(mounting hardware not included). Be careful not to drill into wiring or vehicle |
mechanisms. You are solely responsible for securely fastening the CRZNAUX2 in your vehicle. Make certain that wires and cables cannot be damaged by screws, clips, or sharp, exposed pieces of metal.
Operation
Controlling your Zune device
The CRZNAUX2 will not provide control of your Zune device unless you attach the optional remote, which is available separately. Please visit www.soundgate.com or your local mobile audio dealer for details on the CRZNAUX2 remote’s availability.
Activating the CRZNAUX2
1.Turn on the ignition and factory radio.
2.Ensure that your Zune device is connected and playing audio.
3.Wait several seconds for the factory radio and the CRZNAUX2 to synchronize. Press the MODE button on your factory radio.
The factory radio’s display will report Disc 1, Track
NOTE
If the radio’s display does not report Disc 1, Track 1 after pressing the MODE button and you do not hear music from your Zune device, turn the radio and ignition off. Disconnect the CRZNAUX2 harness from the factory radio’s rear panel. Wait 30 seconds, then reconnect the harness. Repeat steps
This initialization process, if necessary at all, will only need to be performed during the initial installation.
4.To deactivate the CRZNAUX2 and switch your radio back to its normal mode, simply press the MODE button.
Why SoundGate Dealers
have the edge...
The technologies used in today’s vehicles are as sophisticated as any laptop computer. At SoundGate we believe these new technologies are full of opportunities for mobile electronic dealers across the nation. We make it a high priority to not only research these new systems, but to understand them and their impact on the aftermarket car audio industry. Armed with this knowledge, we are well equipped to help you integrate new components into these systems with our innovative, high- performance interfaces and unparalleled technical support.
Ask your autosound specialist about these other exciting SoundGate products...
•Auxiliary Input Interfaces and Docking Stations which allow you to input audio from MP3 Players, DVD/Video, Satellite Radio, and more to OEM and aftermarket car audio systems
•High-performance Radio Replacement
•Interfaces for seamlessly integrating new receivers or CD players into OEM audio systems
•
•Remote Audio Control Interfaces that let you control aftermarket receivers and CD players from your factory rear seat, or steering- wheel mounted audio controls.
•And many others!
Ensure that the Zune dock connector is left in a convenient place for connection to your Zune device. Plug the Zune dock connector in straight. Do not insert the connector at an angle or wiggle the connector during insertion.
Please read the Operation section on the following page and test the installation before reassembling the vehicle dash, trim panels, and audio systems.
www.soundgate.com
Zune™ and the Zune™ logo are trademarks of the Microsoft group of companies.
Copyright©
4 | 5 |
6