TOOL STICKERS & TAGS
WHEEL | SIZE |
|
RPM: | SPINDLE: | PSI |
PRESS: | BAR | |
F L O W: | LPM | GPM |
28728
RS25 Name Tag28811 Information Plaque (CE models only)
CAUTION
PROTECT YOUR EYES - WEAR SAFETY GOGGLES
1.Do not use damaged wheels.
2.Use full throttle only while cutting.
3.Use only wheels marked high speed reinforced that meet requirements
of ANSI B7.5. Wheels should be no larger than 16” diameter x 5/31” thick with a 1” arbor hole and rated for 4700 rpm minimum speed.
4.Inspect wheel guard & collars for damage after any wheel breakage on the machine.
5.Maximum spindle speed is 4700 rpm.
05868
Abrasive
(14 inch models only – except CE)
03787
GPM Sticker
25610
Railroad Help Desk Sticker
28409
Composite Sticker (CE models only)
11207
Sound Power Level Sticker
CAUTION
PROTECT YOUR EYES...
WEAR SAFETY GOGGLES
1.DO NOT USE DAMAGED WHEELS.
2.USE FULL TROTTLE ONLY WHILE CUTTING.
3.USE ONLY WHEELS MARKED HIGH SPEED REINFORCED THAT MEET REQUIREMENTS OF ANSI B7.1,B7.5 WHEELS SHOULD BE NO LARGER THAN 16" DIA X 5/32" THICK WITH A 1" ARBOR HOLE & RATED FOR 4700 RPM MINIMUM SPEED.
4.INSPECT WHEEL GUARD & COLLARS FOR DAMAGE AFTER ANY WHEEL BREAKAGE ON THE MACHINE.
5.MAXIMUM SPINDLE SPEED IS 4700 RPM.
6.READ OPERATION MANUAL.
17641
Abrasive
05152
NOTE:
THE INFORMATION LISTED ON THE STICKERS SHOWN, MUST BE LEGIBLE AT ALL TIMES.
REPLACE DECALS IF
THEY BECOME WORN OR DAMAGED. REPLACEMENTS ARE AVAILABLE FROM YOUR LOCAL STANLEY DISTRIBUTOR.
The safety tag (P/N 15875) at right is attached to the tool when shipped from the factory. Read and understand the safety instructions listed on this tag before removal. We suggest you retain this tag and
D A N G E R
1.FAILURE TO USE HYDRAULIC HOSE LABELED AND CER- TIFIED AS
BEFORE USING HOSE LABELED AND CERTIFIED AS NON- CONDUCTIVE ON OR NEAR ELECTRIC LINES BE SURE THE HOSE IS MAINTAINED AS
2.A HYDRAULIC LEAK OR BURST MAY CAUSE OIL INJEC- TION INTO THE BODY OR CAUSE OTHER SEVERE PERSONAL INJURY.
A.DO NOT EXCEED SPECIFIED FLOW AND PRESSURE FOR THIS TOOL. EXCESS FLOW OR PRESSURE MAY CAUSE A LEAK OR BURST.
B.DO NOT EXCEED RATED WORKING PRESSURE OF HYDRAULIC HOSE USED WITH THIS TOOL. EXCESS PRESSURE MAY CAUSE A LEAK OR BURST.
C.CHECK TOOL HOSE COUPLERS AND CONNECTORS DAILY FOR LEAKS. DO NOT FEEL FOR LEAKS WITH YOUR HANDS. CONTACT WITH A LEAK MAY RESULT IN SEVERE PERSONAL INJURY.
I M P O R T A N T
READ OPERATION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT.
USE ONLY PARTS AND REPAIR PROCEDURES APPROVED BY STANLEY AND DESCRIBED IN THE OPERATION MANUAL.
TAG TO BE REMOVED ONLY BY
TOOL OPERATOR.
SEE OTHER SIDE
D A N G E R
D.DO NOT LIFT OR CARRY TOOL BY THE HOSES. DO NOT ABUSE HOSE. DO NOT USE KINKED, TORN OR DAMAGED HOSE.
3.MAKE SURE HYDRAULIC HOSES ARE PROPERLY CON- NECTED TO THE TOOL BEFORE PRESSURING SYSTEM. SYSTEM PRESSURE HOSE MUST ALWAYS BE CON- NECTED TO TOOL “IN” PORT. SYSTEM RETURN HOSE MUST ALWAYS BE CONNECTED TO TOOL “OUT” PORT. REVERSING CONNECTIONS MAY CAUSE REVERSE TOOL OPERATION WHICH CAN RESULT IN SEVERE PERSONAL INJURY.
4.DO NOT CONNECT
5.BYSTANDERS MAY BE INJURED IN YOUR WORK AREA. KEEP BYSTANDERS CLEAR OF YOUR WORK AREA.
6.WEAR HEARING, EYE, FOOT, HAND AND HEAD PRO- TECTION.
7.TO AVOID PERSONAL INJURY OR EQUIPMENT DAMAGE, ALL TOOL REPAIR MAINTENANCE AND SERVICE MUST ONLY BE PERFORMED BY AUTHORIZED AND PROPERLY TRAINED PERSONNEL.
IM P O R T A N T
READ OPERATION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT.
USE ONLY PARTS AND REPAIR PROCEDURES APPROVED BY STANLEY AND DESCRIBED IN THE OPERATION MANUAL.
TAG TO BE REMOVED ONLY BY
TOOL OPERATOR.
SEE OTHER SIDE
attach it to the tool when not in use.
SAFETY TAG P/N 15875 (Shown smaller then actual size)
RS25 User Manual ◄ 7