Service, Prior to Disassembly | Stanley Black & Decker HD45 specification

SERVICE

Good maintenance practice keeps the drill on the job and increases its service life.

The most important maintenance practice is to keep the hydraulic ﬂ uid clean at all times. Contaminated hydraulic

ﬂuid causes rapid wear and/or failure of internal parts.

Follow the procedure contained in the HYDRAULIC SYS- TEM REQUIREMENTS section of the manual to ensure peak performance from the tool.

Never disassemble the tool unless proper troubleshooting procedures have isolated the problem to an internal part. Disassemble it only to the extent necessary to replace the defective part. KEEP CONTAMINANTS SUCH AS DIRT AND GRIT AWAY FROM INTERNAL PARTS AT ALL TIMES.

Always determine and correct the cause of the problem prior to assembly. Further wear and tool failure can result if the original cause is not corrected.

HAMMER DRILL DISASSEMBLY

4.Remove the two capscrews (3/8 hex socket) and two side rods. Remove handle assembly to expose ON/OFF valve spool and accumulator diaphragm. Remove the mo- tor assembly by tapping the top of the motor ﬂ ange with a plastic or rubber hammer.

5.Remove the accumulator valve block by tapping on its underside with a plastic or rubber hammer. Tap on alter- nate sides to ensure that the valve block comes off straight without binding.

6.Remove piston from the ﬂ ow sleeve assembly.

7.Remove the accumulator diaphragm and ON/OFF valve from accumulator valve block, taking care not to damage the valve stem. The valve, bushing and associated seals will come out as an assembly. Turn the valve block upside down to remove valve spring.

8.Clamp the accumulator valve body in a bench vise with the IN/OUT ports facing up.

IMPORTANT

Do not overtighten the vise and distort the block.

PRIOR TO DISASSEMBLY

Clean exterior of tool.

Obtain Seal Kit (Part Number 05839). Replace all seals ex- posed during disassembly. Note orientation of seals before removing them. Install new seals in the same way.

DISASSEMBLY

1.Secure the drill in a bench vise with the “IN” and “OUT” ports up, clamping on the ﬂ ow sleeve tube between the side rods. Soft vise jaws are recommended.

2.Remove the pigtail hose assemblies.

Note:

The drill is full of oil and will drip from the ports when the hoses are removed.

3. Remove the charge valve cap from the top of the handle.

WARNING

Discharge accumulator.

9.Remove the porting block with a 3/8-16 thread slide hammer or Tamper Sleeve Tool (part number 01120).

FLOW SLEEVE DISASSEMBLY

1.Remove the piston if not previously removed.

2.Place the ﬂ ow sleeve assembly, automatic valve body down, on Flow Sleeve Removal Tool (part number 04919), which in turn is placed on Flow Sleeve Removal Tube (part number 04910).

3.With an arbor press and using an aluminum disc to pro- tect the ﬂ ow sleeve, push on the ﬂ ow sleeve to remove the automatic valve body.

IMPORTANT

Use a rag in the bottom of the removal tube to protect the automatic valve body when it drops out.

4.The automatic valve, four 1/4 x 1-1/2 inch push pins from the ﬂ ow sleeve and two 3/16 x 1-1/4 inch push pins from the automatic valve body will come out.

HD45 specifications

The Stanley Black & Decker HD45 is a powerful and versatile tool designed for professionals and DIY enthusiasts alike. This rugged and durable hammer drill is engineered to handle a variety of tasks, making it a go-to solution for both construction sites and home improvement projects. With a focus on performance, practicality, and safety, the HD45 brings together innovative features and advanced technologies to deliver exceptional results.

One of the standout features of the HD45 is its robust motor, which delivers high torque and variable speeds, allowing users to drill through various materials such as wood, fiberglass, and metal with ease. The drill's two-speed settings enable users to switch between high-speed drilling and high-torque applications, providing versatility for different types of jobs. This adaptability ensures that the HD45 can take on challenging tasks without compromising on efficiency.

Another important characteristic of the HD45 is its ergonomic design. The drill is equipped with a comfortable, non-slip grip that allows for better control during operation, reducing user fatigue over extended use. Additionally, the compact and lightweight construction makes it easy to maneuver in tight spaces, which is particularly helpful when working on intricate projects or reaching overhead.

The HD45 also integrates several advanced technologies to enhance its usability and performance. One such technology is the electronic clutch, which provides precise control over torque settings. This feature prevents overdriving screws and allows for consistent results across various materials. Furthermore, the built-in LED work light illuminates the workspace, providing visibility in dimly lit areas and ensuring accurate drilling every time.

Safety is a top priority for Stanley Black & Decker, and the HD45 reflects this commitment. The drill is equipped with a robust safety switch that prevents accidental startups, ensuring that users can handle the tool with confidence. Additionally, the durable housing of the drill is designed to withstand heavy-duty use, offering longevity and reliability on the job.

In conclusion, the Stanley Black & Decker HD45 is a high-performance hammer drill that combines power, versatility, and safety features. With its advanced motor, ergonomic design, and innovative technologies, it is an indispensable tool for anyone looking to tackle a wide range of drilling and fastening tasks. Whether for professional construction or home improvement, the HD45 is ready to deliver outstanding results.