Tool Stickers & Tags

CAUTION

PROTECT YOUR EYES

WEAR SAFETY GOGGLES

Do not use damaged wheels use full throttle only while grinding.

Use only reinforced resinoid wheels rated for 6500 RPM minimum 9 inch diameter by inch thick maximum. Inspect wheel

28811

Information Plaque

28322 CE Decal

WARNING

Grinding Wheel and Jam nut must be tightened with a wrench before use.

10396 Warning Decal

28409 Composite Decal

40 LPM @ 138 BAR EHTMA CATEGORY

12535

Circuit Type E Decal

11206

Circuit Type C Decal

guard for signs of damage after

any wheel failure.

08688 Safety Decal

4-12 GPM / 15-45 LPM

DO NOT EXCEED 2000 PSI / 140 BAR

DO NOT EXCEED SPECIFIED FLOW OR PRESSURE

USE CLOSED-CENTER TOOL ON CLOSED-CENTER

SYSTEM. USE OPEN-CENTER TOOL ON OPEN-CENTER

SYSTEM. CORRECTLY CONNECT HOSES TO TOOL “IN”

AND “OUT” PORTS. IMPROPER HANDLING, USE OR OTHER

MAINTENANCE OF TOOL COULD RESULT IN A LEAK, BURST

OR OTHER TOOL FAILURE. CONTACT AT A LEAK OR BURST

CAN CAUSE OIL INJECTION INTO THE BODY. FAILURE TO

OBSERVE THESE PRECAUTIONS CAN RESULT IN SERIOUS

PERSONAL INJURY.

03788 GPM Decal

The safety tag (p/n 15875) at right is attached to the tool when shipped from the factory. Read and understand the safety instructions listed on this tag before removal. We suggest you retain this tag and attach it to the tool when not in use.

D A N G E R

1.FAILURE TO USE HYDRAULIC HOSE LABELED AND CERTI-

FIED AS NON-CONDUCTIVE WHEN USING HYDRAULIC

TOOLS ON OR NEAR ELECTRICAL LINES MAY RESULT IN DEATH OR SERIOUS INJURY.

BEFORE USING HOSE LABELED AND CERTIFIED AS NON- CONDUCTIVE ON OR NEAR ELECTRIC LINES BE SURE THE HOSE IS MAINTAINED AS NON-CONDUCTIVE. THE HOSE SHOULD BE REGULARLY TESTED FOR ELECTRIC CURRENT

LEAKAGE IN ACCORDANCE WITH YOUR SAFETY DEPART- MENT INSTRUCTIONS.

2.A HYDRAULIC LEAK OR BURST MAY CAUSE OIL INJECTION INTO THE BODY OR CAUSE OTHER SEVERE PERSONAL INJURY.

A.DO NOT EXCEED SPECIFIED FLOW AND PRESSURE FOR THIS TOOL. EXCESS FLOW OR PRESSURE MAY

CAUSE A LEAK OR BURST.

B.DO NOT EXCEED RATED WORKING PRESSURE OF HYDRAULIC HOSE USED WITH THIS TOOL. EXCESS

PRESSURE MAY CAUSE A LEAK OR BURST.

C.CHECK TOOL HOSE COUPLERS AND CONNECTORS DAILY FOR LEAKS. DO NOT FEEL FOR LEAKS WITH YOUR HANDS. CONTACT WITH A LEAK MAY RESULT

IN SEVERE PERSONAL INJURY.

I M P O R T A N T

READ OPERATION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT.

USE ONLY PARTS AND REPAIR PROCEDURES APPROVED BY STANLEY AND DESCRIBED IN THE OPERATION MANUAL.

TAG TO BE REMOVED ONLY BY

TOOL OPERATOR.

SEE OTHER SIDE

D A N G E R

D.DO NOT LIFT OR CARRY TOOL BY THE HOSES. DO NOT ABUSE HOSE. DO NOT USE KINKED, TORN OR DAMAGED HOSE.

3.MAKE SURE HYDRAULIC HOSES ARE PROPERLY CON- NECTED TO THE TOOL BEFORE PRESSURING SYSTEM.

SYSTEM PRESSURE HOSE MUST ALWAYS BE CON- NECTED TO TOOL “IN” PORT. SYSTEM RETURN HOSE

MUST ALWAYS BE CONNECTED TO TOOL “OUT” PORT.

REVERSING CONNECTIONS MAY CAUSE REVERSE

TOOL OPERATION WHICH CAN RESULT IN SEVERE

PERSONAL INJURY.

4.DO NOT CONNECT OPEN-CENTER TOOLS TO CLOSED- CENTER HYDRAULIC SYSTEMS. THIS MAY RESULT IN

LOSS OF OTHER HYDRAULIC FUNCTIONS POWERED BY

THE SAME SYSTEM AND/OR SEVERE PERSONAL INJURY.

5.BYSTANDERS MAY BE INJURED IN YOUR WORK AREA. KEEP BYSTANDERS CLEAR OF YOUR WORK AREA.

6.WEAR HEARING, EYE, FOOT, HAND AND HEAD PRO- TECTION.

7.TO AVOID PERSONAL INJURY OR EQUIPMENT DAMAGE, ALL TOOL REPAIR MAINTENANCE AND SERVICE MUST ONLY BE PERFORMED BY AUTHORIZED AND PROPERLY TRAINED PERSONNEL.