Lincoln Electric SVM155-A service manual Main Transformer T1 Voltage Test

Page 45

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

F-17F-17

TROUBLESHOOTING & REPAIR

MAIN TRANSFORMER (T1) VOLTAGE TEST

WARNING

Service and repair should be performed only by Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment could result in danger to the technician or the machine operator and will invalidate your factory warranty. For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed throughout this manual.

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact the Lincoln Electric Service Department for technical troubleshooting assistance before you proceed. Call (800) 833-9353 (WELD).

TEST DESCRIPTION

This test will determine if the correct voltages are being:

a.applied to the primary windings of the Main Transformer (T1).

b.induced on the secondary windings, fan winding, and phase angle windings.

MATERIALS NEEDED

Volt/Ohm Meter

MULTI-SOURCE wiring diagrams (See Electrical Diagram Section of Manual). 3/8” Nut Driver

This procedure takes approximately 45 minutes to perform.

MULTI-SOURCE

Page 44 Page 46
Image 45
Page 44 Page 46
Contents MULTI-SOURCE TM California Proposition 65 Warnings SafetyElectric Shock can kill Welding Sparks can cause fire or explosion Sûreté Pour Soudage a L’Arc Précautions DE SûretéMaster Table of Contents for ALL Sections Table of Contents Installation Section Technical Specifications Multi-Source K1752-1 InstallationSelect Proper Location Safety PrecautionsStacking TiltingInput and Grounding Connections Fuse and Wire SizesParalleling Output ConnectionsMULTI-SOURCE Table of Contents Operation Section Operation Safety InstructionsDesign Features and ADVAN- Tages General DescriptionRecommended EQUIPMENT/PROCESSES Recommended EQUIPMENT/CONNECTIONS Controls and SettingsTable of Contents Accessories Field Installed Options / Accessories Factory Installed Options / AccessoriesTable of Contents Maintenance Routine and Periodic MAINTE- Nance Safety PrecautionsFigure D.1 Major Component Location MULTI-SOURCE Table of Contents Theory of Operation Input VOLTAGE, FILTER, Contac TOR and Control Trans Former General DescriptionReturn to Section Section TOC Troubleshooting & RepairOperation Protection Devices and CIR Cuits Figure E.5 SCR Operation SCR OperationTable of Contents Troubleshooting & Repair Section HOW to USE Troubleshooting Guide Electric Shock can kill PC Board Troubleshooting Procedures and ReplacementTroubleshooting Guide Perform the Firing Board Test Calibration ProcedurePerform the Main Transformer T1 TestCircuit external to the Multi Main Transformer Test Technical SpecificationsInput Contactor Test Functions ProblemsControl Transformer T2 Voltage Test Test DescriptionFigure F.1. Control Transformer Location & Leads Test Procedure575 VAC 43.0 VAC 460 VAC 34.50 VAC 380 VAC 28.50 VAC Secondary Thermostat Input Contactor Test 241COIL Input Contactor TestTest for Contact Continuity Removal and Replacement ProcedureMULTI-SOURCE Main Transformer T1 Voltage Test Contactor Test Main Transformer T1 Voltage TestFigure F.6. Main Secondary Lead Test Points MULTI-SOURCE Static SCR Test Static SCR Test Leads Remove Red Paint Active SCR Test Active SCR Test Active SCR Test Remove Red Paint SW1 MULTI-SOURCE Control Board Test See Figure F.15 Control Board Test#341 #230 #215 #231 #263 #201 J1 MULTI-SOURCE Firing Board Test Static and Active SCR Tests Figure F.17Then Table F.2. LED 7, 8 and 9 Check List#231 #215 #340 J8 #287 MULTI-SOURCE Meter Accuracy Check Control Board Normal Open Circuit Voltage Waveform no Load Volts Typical SCR Gate Voltage Waveform no Load MULTI-SOURCE Description Input Contactor Cleaning AND/OR ReplacementRemoval Procedure Coil 240MULTI-SOURCE Control Board Replacement Procedure Control Board Firing Board Replacement Procedure Firing Board SCR Bridge / Heat Sink Assembly Replacement Procedure Bridge Assembly Mount #251 Mounting Bolt Removal of Individual SCR Heat Sink Assemblies Figure F.27 See Figure F.26No Load Readings FAN OFF Maximum Open Circuit VoltagePerform Meter Accuracy Test MULTI-SOURCE Table of Contents Electrical Diagrams Section Electrical DiagramsMULTI-SOURCE Wiring DiagramSchematic Control PC Board Return to Section PC Board ASSEMBLY-CONTROLSchematic Firing Printed Circuit Board TP1 PC Board ASSEMBLY-FIRINGM14312 PC Board Assembly SnubberSVM Error Reporting Form

SVM155-A specifications

The Lincoln Electric SVM155-A is a state-of-the-art welding machine that excels in versatility and performance, making it ideal for both professional welders and hobbyists. This multi-process welder supports MIG, TIG, and stick welding processes, allowing users to tackle a wide range of applications with a single device. Its user-friendly design and advanced technology make it an exceptional choice for those looking to enhance their welding capabilities.

One of the main features of the SVM155-A is its robust power output, which can handle welding materials ranging from thin sheets to heavier stock. The welder offers a high duty cycle, ensuring that users can work efficiently without the need for prolonged breaks. This is especially important in industrial settings where productivity is key. Additionally, the SVM155-A is equipped with a digital display that allows for easy monitoring and precise control of the welding parameters, ensuring consistency in weld quality.

The European-designed INVERTER technology embedded in the SVM155-A significantly contributes to its lightweight and compact design. Weighing in at only 19.4 lbs, this welder is portable and ideal for fieldwork or workshops where space is limited. The inverter technology not only reduces the size and weight but also improves energy efficiency, leading to lower operational costs over time.

The SVM155-A also features advanced safety mechanisms, including over-current protection to safeguard the machine from potential damage during excessive use. It also includes a thermal overload shut-off, which prevents overheating, ensuring a longer lifespan for the welder.

Another standout characteristic of the SVM155-A is its exceptional arc stability and ease of use. The machine is designed to provide a smooth and consistent arc, reducing spatter and ensuring clean welds. Moreover, the welder is compatible with a wide range of materials, including stainless steel, aluminum, and carbon steel, further enhancing its versatility.

In conclusion, the Lincoln Electric SVM155-A is a powerful, durable, and multifunctional welding machine that incorporates advanced technologies to meet the needs of modern welding applications. Its portability, safety features, and ability to deliver high-quality welds make it an excellent investment for anyone looking to improve their welding skills or expand their capabilities in various welding projects.
Top Page Image Contents